Cadel nice - PROGRAMMING FUNCTIONS; Clock and Daily Programming Setup; Weekend Scheduling; Weekly Scheduling

20
NICE - MIRIAM - CRISTAL - PRETTY - KRISS - MARY - TECNA - EVO
EN
If the pellets are of bad quality (if contains sizing agents, oils, varnishes, plastic remains or if
it is mealy), deposits will form along pellets drop pipe during the running. When the stove is
switched off, these remains could form little hot coals that rising along the pipe could reach
the pellets on the hopper burning them and creating a thick and harmful smoke inside the
room. Please always keep the hopper closed with its own lid. If the pipe is sooty, please
clean it (see INTRODUCTION page 23).
11.13 CLOCK SETTING
• Press P3 key and then P5 key till underlining “SET CLOCK” menu (02).
• Press once P3 (DAY) and with P1 and P2 keys select the day of the week (Monday, Tuesday, Wednesday,
Thursday, Friday, Saturday, Sunday).
• Press for the second time P3 key (HOURS) and with P1 and P2 keys set the hour.
• Press for the third time P3 key (MINUTES) and with P1 and P2 keys select the minutes. Press for the fourth time
P3 key (DAY) and with P1 and P2 keys select the day of the month (1,2,3...29,30,31).
• Press for the fth time P3 key (MONTH) and with P1 and P2 keys select the month:
• Press for the sixth time P3 key (YEAR) and with P1 and P2 keys select the year.
• To exit from the programme press P4 twice.
11.14 DAILY PROGRAMMING
It allows to enable, disable and settle the daily chronothermostat functions.
Press P3 key and then P5 key till the menu “SET CHRONO”. Press once P3 key and with P5 and P6 keys select
the “PROGRAM DAY”. Press once P3 till nding “CHRONO DAY”. With P1 and P2 keys put in “OFF” or “ON”. It is
possible to set two working times delimited by the set times.
After “CHRONO DAY”:
• Press P5: the display shows “START 1”, with P1 and P2 keys set the ignition time value or put in “OFF”.
• Press P5: the display shows “STOP 1”, with P1 and P2 keys set the switching off time value or put in “OFF”.
• Press P5: the display shows “START 2”, with P1 and P2 keys set the ignition time value or put in “OFF”.
• Press P5: the display shows “STOP 2”, with P1 and P2 keys set the switching off time value or put in “OFF”.
• Press P4 key three times to exit from the menu.
11.15 WEEK-END PROGRAMMING
It allows to enable, disable and settle the chronothermostat functions during saturday and sunday.
Press P3 key and then P5 key till the menu “SET CHRONO”. Press once P3 key and with P5 and P6 keys select
“PROGRAM WEEK-END”. Press once P3 till nding “CHRONO WEEK-END”. With P1 and P2 keys put in “OFF” or
“ON”.
It is possible to set two working times delimited by the set times and valid only for saturday and sunday.
After “CHRONO WEEK-END”:
• Press P5: the display shows “START 1 WEEK-END”, with P1 and P2 keys set the ignition time value or put in “OFF”.
• Press P5: the display shows “STOP 1 WEEK-END”, with P1 and P2 keys set the switching off time value or put in
“OFF”.
• Press P5: the display shows “START 2 WEEK-END”, with P1 and P2 keys set the ignition time value or put in “OFF”.
• Press P5: the display shows “STOP 2 WEEK-END”, with P1 and P2 keys set the switching off time value or put in
“OFF”.
• Press P4 key three times to exit from the menu.
11.16 WEEKLY PROGRAMMING
It allows to enable, disable and settle the weekly hermostat functions (saturday and sunday included).
Press P3 key and then P5 key till the menu “SET CHRONO”. Press once P3 key and with P5 and P6 keys select
“PROGRAM WEEK”. Press once P3 till nding “WEEKLY CHRONO”. With P1 and P2 keys put in “OFF” or “ON”. It is
possible to set four working times delimited by the set times.
After “WEEKLY CHRONO”:
Press P5: the display shows “START PROG-1”, with P1 and P2 keys insert the ignition time value or put in “OFF”.
Press P5: the display shows “STOP PROG-1”, with P1 and P2 insert the switching off value or put in “OFF”.
• Press P5: the display shows “MONDAY PROG-1”, with P1 and P2 keys set “ON” or “OFF”.
• Press P5: the display shows “TUESDAY PROG-1”, with P1 and P2 keys set “ON” or “OFF”.
• Press P5: the display shows “WEDNESDA PROG-1”, with P1 and P2 keys set “ON” or “OFF””.
• Press P5: the display shows “THURSDAY PROG-1”, with P1 and P2 keys set “ON” or “OFF”.
• Press P5: the display shows “FRIDAY PROG-1”, with P1 and P2 keys set “ON” or “OFF”.
• Press P5: the display shows “SATURDAY PROG-1”, with P1 and P2 keys set “ON” or “OFF””.
• Press P5: the display shows “SUNDAY PROG-1”, with P1 and P2 keys set “ON” or “OFF”.
• Now press P5 and repeat all the previous instructions for Prog-2, Prog-3, Prog-4.
• To exit press three times P4.