Case CX130C - Page 34

To Next Page

To Previous Page

2-SAFETYINFORMATION

SMIL20CEX1386HA2

2-18

Main Page

Table of Contents2
General Information7
Note to the Owner7
Intended Use8
Electro-Magnetic Compatibility (EMC)8
Telematics8
Manual Scope and Required Training Level9
Product Identification11
Operator's Manual Storage on the Machine14
Machine Orientation14
Machine Components15
Safety Information17
Signal Word Definitions17
Safety Rules18
Ecology and the Environment27
Hand Signals28
Safety Signs32
Controls and Instruments47
Access to Operator's Platform47
Door and Steps47
Operator's Seat49
Forward Controls53
Forward Controls (Optional)56
Windshield60
Front Lower Window61
Left-Hand Side Controls62
Gate Lock Lever and Safety Bar64
Heating, Ventilation or Air-Conditioning Control65
Cab Internal Lighting69
Emergency Exit Hammer69
Sliding Windows on Door69
Right-Hand Side Controls70
Dozer Blade Control Lever73
Instrument Cluster74
Radio90
Rearward Controls93
Fuse Box93
Magazine Rack93
Refrigerated/Heated Compartment93
Storage Compartment94
Coat Hanger Hook94
Overhead Controls95
Roof Curtain95
Roof Hatch95
Sunshield (if Equipped)95
Exterior Controls96
Cab Protection (ROPS and FOPS)96
Rain Deflector (if Equipped)97
Mirrors98
Cameras101
Side Doors103
Engine Hood105
Lower Panels106
Windshield Washer Reservoir106
Towing Holes107
Front Storage Box108
Fire Extinguisher108
Fuel Tank109
Fuel Tank Filler Pump (if Equipped)110
Operating Instructions113
Starting the Unit113
Anti-Theft Protection113
Starting the Engine115
Bringing the Machine up to Operating Temperature117
Operating the Machine in Hot or Cold Weather119
Operating the Machine120
Lowering the Attachment in the Event of a Failure123
Bucket Replacement125
Stopping the Unit127
Stopping the Engine127
Moving the Unit128
Machine Travel128
Parking the Unit132
Parking the Machine132
Transport Operations135
Road Transport135
Transporting Precautions (Machine Equipped with Long Arm)135
Loading the Machine Onto a Transport Trailer136
Tie Downs for Shipping141
Unloading the Machine from a Transport Trailer145
Shipping Transport147
Lifting the Machine with a Crane147
Recovery Transport149
Towing the Machine149
Maintenance151
General Information151
Basic Instructions151
Fluids and Lubricants154
Engine Oil Recommended Operating Temperature Range157
Releasing Pressure in the Hydraulic System158
Fuel System Bleeding159
Protecting the Electronic and Electrical Systems During Battery Charging or Welding162
Maintenance Planning163
Maintenance Chart163
Break-In Period165
Grease Points (Bucket)165
Cab Protection (ROPS and FOPS)165
Tightening Torques165
Track Shoe Bolt Torque165
Hydraulic Oil Return Filter165
Pilot Line Filter165
Swing Reduction Unit Oil165
Travel Reduction Units Oil165
Every 10 Hours166
Engine Oil Level166
Engine Coolant Level167
Hydraulic Oil Level168
Fan and Alternator Drive Belt169
Fuel Tank Drain169
Fuel Pre-Filters170
Air Conditioner Filters171
Grease Points (Blade)173
Every 250 Hours174
Grease Points (Bucket)174
Swing Reduction Unit Oil175
Travel Reduction Units Oil176
Engine Primary Air Filter177
Battery Electrolyte Level180
Fan and Alternator Drive Belt183
Hydraulic Oil Tank185
Tightening Torques186
Track Shoe Bolt Torque187
Track Rollers and Idler Wheels188
Cab Protection (ROPS and FOPS)188
Every 500 Hours189
Turntable Bearing189
Engine Oil and Filter191
Fuel Pre-Filter193
Fuel Filter195
Radiator and Coolers196
Every 1000 Hours197
Grease Points (Boom and Arm)197
Hydraulic Tank Breather200
Engine Air Filters201
Hydraulic Fluid Analysis204
Engine Valve Rocker Clearance Adjustment204
Swing Reduction Unit Oil205
Travel Reduction Units Oil207
Alternator208
Starter Motor208
Every 2000 Hours209
Hydraulic Oil Suction Filter209
Hydraulic Oil Return Filter210
Pilot Line Filter211
Air Conditioner Filters212
Swing Reduction Gear212
Every 4000 Hours213
Engine Coolant213
Pump Outlet Hoses218
Hydraulic Hoses218
Every 5000 Hours219
Hydraulic Oil and Filters219
When Necessary222
Fuel Feed Pump222
Track Tension223
Fuel Tank Strainer225
Gas Spring Inspection226
Bulb Replacement227
Bucket Teeth230
Cylinders232
Plastic and Resin Parts232
Air Conditioning System233
Fuse and Relay Locations235
Fuses235
Storage237
Preparing for Storage237
Periodic Checks238
Starting up the Machine239
Troubleshooting241
Fault Code Resolution241
Engine Troubleshooting241
Specifications243
Machine Specifications243
Fluids and Lubricants245
Dimensions248
Operating Weights253
Accessories255
Direct Fit Buckets255
Auxiliary Hydraulic Circuits256
Hydraulic Quick Coupling System265
Loads Handling269
Air Suspension Seat273
Front Guard Protective System277

Case CX130C - Page 34

Table of Contents

Related product manuals