Configuring Function Settings
EN-118
The Examination Mode changes the operation of the Digital
Keyboard as described below to provide support for those
taking a musical instrument grade test.
● Accompaniment Pattern Operations
• If the Digital Keyboard is in synchro start standby (page
EN-48) while ACCOMP is off ([ACCOMP] indicator not
displayed), rhythm will start when you play something
anywhere on the keyboard. Synchro start standby is exited
at this time.
• Rhythm will not start even if you press bo INTRO, or
bp VARIATION/FILL-IN 1 to bs VARIATION/FILL-IN
4 while rhythm play is stopped. Instead, each
accompaniment pattern becomes selected and the
corresponding indicators ([ I ], [V1] to [V4]) flash on the
display.
• Pressing bp VARIATION/FILL-IN 1 to bs VARIATION/
FILL-IN 4 while an accompaniment pattern’s intro is
sounding immediately sounds a fill-in (1 to 4) and sounds
the variation that corresponds to the button that was
pressed.
• Pressing bp VARIATION/FILL-IN 1 to bs VARIATION/
FILL-IN 4 while variation 1 to 4 of an accompaniment
pattern is sounding immediately switches to the
accompaniment pattern, even part way through a measure.
• The registration function saves the accompaniment pattern
selection status.
● Split Point Settings
• The correspondence between note numbers and note
names is Note Number 60 = C3. (C4 when Examination
Mode is turned off.)
• For the split point, lower point, and chord point explained
under “Advanced Split Settings” (page EN-50), you press a
keyboard key to specify the upper limit of the LOWER part
keyboard (or accompaniment keyboard) in the Examination
Mode.
1.
Press bk FUNCTION.
2.
Use the [1] (V) and [3] (W) bm number keys
to display “Other”, and then press [6] (ENTER).
3.
Use the [1] (V) and [3] (W) keys to display
“ExamMode”.
4.
Press bn [–] or [+] to turn on the setting.
5.
When the setting is the way you want, long-
press the [4] (EXIT) bm number key to exit the
setting screen.
You can use the procedure below to return the data and
settings to their initial factory defaults.
• The procedure below deletes all of the following data
stored in Digital Keyboard memory: user tones, user
rhythms, registration data, MIDI recorder song data.
Backup of important data to a USB flash drive (page
EN-119) or computer (page EN-125) is recommended.
1.
Press bk FUNCTION.
2.
Use the [1] (V) and [3] (W) bm number keys
to display “Other”, and then press [6] (ENTER).
3.
Use the [1] (V) and [3] (W) keys to display
“Reset”, and then press [6] (ENTER).
4.
Use the [1] (V) and [3] (W) keys to display
“Factory”, and then press [6] (ENTER).
This displays “Sure?”
5.
Press bn [+] (YES) to execute the factory reset
or bn [–] (NO) to cancel.
• To exit the operation, long-press the [4] (EXIT) bm
number key.
You can use bk FUNCTION to return all Digital Keyboard
settings to their initial factory defaults.
Perform the procedure under “To configure function settings
with the bk FUNCTION button” (page EN-112), and perform
the following operation to select setting reset:
Other (Other) 3 Reset (Reset) 3 Setting reset (Setting)
(page EN-117). Next, execute the reset.
Examination Mode
To enter the Digital Keyboard’s Examination
mode
Batch Deleting Data from Digital
Keyboard Memory
To return all Digital Keyboard settings and
data to their initial factory defaults (Factory
Reset)
To return all Digital Keyboard settings to
their initial factory defaults (Setting Reset)
CTX5000_3000_EN.book 118 ページ ２０１８年２月２６日 月曜日 午後３時５６分
To Next Page
Loading...
Need help?
General
Weight and Dimensions
