Cisco III - Supervisor Engine III User Manual

2-33
Catalyst Supervisor Engine 32 PISA Cisco IOS System Message Guide, Release 12.2ZY
OL-11469-02
Chapter 2 Messages and Recovery Procedures
C7600_SIP200_SPITX Messages
Error Message %C7600_SIP200_SPITX-3-DESCR_ERR_SPA2: SPAstatus=[hex],
syndrome=[hex], RdRspOvf=[int], RdRspTo=[int], OvfVal=[int], OvfCh=[int],
OvfDescHi=[hex], OvfDescLo=[hex], DisChk=[int], SeqErrVal=[int], SeqErrCh=[int]
Explanation
The egress SPI4.2 device on the line card detected a sequence or FIFO overflow error
while processing a TX descriptor. This condition could cause packets to drop.
Recommended Action If this problem recurs, search for resolved software issues using the Bug
Toolkit at http://tools.cisco.com/Support/BugToolKit/ under Product cat6000. If you still require
assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create or contact your Cisco technical support
representative and provide the representative with the output of the show tech-support command
for the line card and the show platform hardware spi4 spa-id efc channel [channel-id] command
for the SPA.
Error Message %C7600_SIP200_SPITX-3-DESCR_ERR_SPA3: SPAstatus=[hex],
syndrome=[hex], RdRspOvf=[int], RdRspTo=[int], OvfVal=[int], OvfCh=[int],
OvfDescHi=[hex], OvfDescLo=[hex], DisChk=[int], SeqErrVal=[int], SeqErrCh=[int]
Explanation
The egress SPI4.2 device on the line card detected a sequence or FIFO overflow error
while processing a TX descriptor. This condition could cause packets to drop.
Recommended Action If this problem recurs, search for resolved software issues using the Bug
Toolkit at http://tools.cisco.com/Support/BugToolKit/ under Product cat6000. If you still require
assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create or contact your Cisco technical support
representative and provide the representative with the output of the show tech-support command
for the line card and the show platform hardware spi4 spa-id efc channel [channel-id] command
for the SPA.
Error Message %C7600_SIP200_SPITX-3-DMA_SQERR: Syndrome=[hex], SPA=[int], Ch=[int],
RdSz=[int], RdOff=[int][chars]
Explanation
The egress SPI4.2 device on the line card detected a sequence error while processing a
DMA operation. This condition could cause packets to drop.
Recommended Action If this problem recurs, search for resolved software issues using the Bug
Toolkit at http://tools.cisco.com/Support/BugToolKit/ under Product cat6000. If you still require
assistance, open a case with the Technical Assistance Center via the Internet
http://tools.cisco.com/ServiceRequestTool/create or contact your Cisco technical support
representative and provide the representative with the output of the show tech-support command
for the line card and the show platform hardware spi4 spa-id efc channel [channel-id] command
for the SPA.
Error Message %C7600_SIP200_SPITX-3-EFC_ERR_SPA0: SPAstatus=[hex][chars]
Explanation
The egress data path device on the line card detected an error condition with the
extended flow control bus interface. This condition could cause packets to drop.
Recommended Action If this problem recurs, search for resolved software issues using the Bug
Toolkit at http://tools.cisco.com/Support/BugToolKit/ under Product cat6000. If you still require
assistance, open a case with the Technical Assistance Center via the Internet

Cisco III - Supervisor Engine III Specifications

General

Brand	Cisco
Model	III - Supervisor Engine III
Category	Software
Language	English