Cisco Nexus 9000 Series - Page 274

FEX MAC Port QoS [fex-mac-qos] size = 0
IPV4 VACL [vacl] size = 512
IPV6 VACL [ipv6-vacl] size = 0
MAC VACL [mac-vacl] size = 0
IPV4 VLAN QoS [vqos] size = 0
IPV6 VLAN QoS [ipv6-vqos] size = 0
MAC VLAN QoS [mac-vqos] size = 0
IPV4 RACL [racl] size = 512
IPV6 RACL [ipv6-racl] size = 0
IPV4 Port QoS Lite [qos-lite] size = 0
FEX IPV4 Port QoS Lite [fex-qos-lite] size = 0
IPV4 VLAN QoS Lite [vqos-lite] size = 0
IPV4 L3 QoS Lite [l3qos-lite] size = 0
Egress IPV4 QoS [e-qos] size = 0
Egress IPV6 QoS [e-ipv6-qos] size = 0
Egress MAC QoS [e-mac-qos] size = 0
Egress IPV4 VACL [vacl] size = 512
Egress IPV6 VACL [ipv6-vacl] size = 0
Egress MAC VACL [mac-vacl] size = 0
Egress IPV4 RACL [e-racl] size = 256
Egress IPV6 RACL [e-ipv6-racl] size = 0
Egress IPV4 QoS Lite [e-qos-lite] size = 0
IPV4 L3 QoS [l3qos] size = 0
IPV6 L3 QoS [ipv6-l3qos] size = 0
MAC L3 QoS [mac-l3qos] size = 0
Ingress System size = 256
Egress System size = 256
SPAN [span] size = 256
Ingress COPP [copp] size = 256
Ingress Flow Counters [flow] size = 0
Egress Flow Counters [e-flow] size = 0
Ingress SVI Counters [svi] size = 0
Redirect [redirect] size = 512
NS IPV4 Port QoS [ns-qos] size = 256
NS IPV6 Port QoS [ns-ipv6-qos] size = 0
NS MAC Port QoS [ns-mac-qos] size = 0
NS IPV4 VLAN QoS [ns-vqos] size = 256
NS IPV6 VLAN QoS [ns-ipv6-vqos] size = 0
NS MAC VLAN QoS [ns-mac-vqos] size = 0
NS IPV4 L3 QoS [ns-l3qos] size = 256
NS IPV6 L3 QoS [ns-ipv6-l3qos] size = 0
NS MAC L3 QoS [ns-mac-l3qos] size = 0
VPC Convergence [vpc-convergence] size = 256
IPSG SMAC-IP bind table [ipsg] size = 0
Ingress ARP-Ether ACL [arp-ether] size = 0
ranger+ IPV4 QoS Lite [rp-qos-lite] size = 0
ranger+ IPV4 QoS [rp-qos] size = 256
ranger+ IPV6 QoS [rp-ipv6-qos] size = 256
ranger+ MAC QoS [rp-mac-qos] size = 256
NAT ACL[nat] size = 0
Mpls ACL size = 0
Ingress IPv4 N3K QoS size = 0
Ingress IPv6 N3K QoS size = 0
MOD RSVD size = 0
sFlow ACL [sflow] size = 0
mcast bidir ACL size = 0
Openflow size = 0
This example shows how to revert to the default RACL TCAM region size:
switch(config)# no hardware profile tcam region racl 512
[SUCCESS] New tcam size will be applicable only at boot time.
You need to 'copy run start' and 'reload'
switch(config)# copy running-config startup-config
Cisco Nexus 9000 Series NX-OS Security Configuration Guide, Release 9.x
248
Configuring IP ACLs
Configuring ACL TCAM Region Sizes