36
• Before starting up the machine, carefully read this manual and the manual of any combustion engine
equipping the machine. In particular, make sure you have fully understood how the machine works as
regards liquid on/o operations.
• The machine is not intended to be used by people (including children) with reduced physical, sensorial
or mental capacities, or who lack the experience and expertise, unless they are able to benet, through
the intermediation of a person responsible for their safety, from supervision or instructions concerning
the use of the machine and of any combustion engine equipping the machine.
• Children must be supervised to make sure they do not play with the machine.
• Pay particular attention when using the machine where vehicles are moving that could possibly drive
over the power lead, delivery pipe or lance and possibly ruin them.
• Observe the safety warnings given in the manual of any optional accessories used.
• Before starting the machine it must be put in a dry place, on a at and stable surface to avoid any falls or
tipping over.
• Carry out the steps described in the
“STOP”
paragraph before moving the machine.
• Before using the machine, wear garments that guarantee adequate protection from erroneous manoeuvres
with the jet of pressurised uid and from the chemical products used.
• During operation:
- always keep an eye on the machine and out of the reach of children; in particular, be very careful when
using near nurseries, clinics and old-people's homes, in case of children, elderly people or disabled
people without supervision;
- do not direct high-pressure jets against materials containing asbestos or other substances harmful for
the health;
- do not cover the machine and do not place it where ventilation is prevented (remember this above all
when using the machine in closed environments); do not use the machine on closed premises if it is
driven by a combustion engine;
- when not in operation, before leaving it without supervision, even for a short time, prior to all topping up
with the chemical product and before doing any jobs, perform the operations described in the
“STOP”
paragraph. In particular, do not leave the machine with the plug in the power socket (in the case of a
machine equipped with combustion engine, disconnecting the spark plug contact is equivalent to
removing the plug from the power socket);
- operating pressure must never exceed the maximum set for the machine (see also
“SPECIFICATIONS
AND TECHNICAL DATA”
paragraph);
- in the case of a thermal or ampere cut-out protection with automatic setting tripping, always move the
master switch to“0” position and, if present, remove the plug from the power socket because, once
cooled, the machine could start up again on its own;
- use adequate personal protective equipment to safeguard against noise emissions (e.g., ear mus);
- grip the lance rmly because when you use the control lever to dispense the product there will be a
kickback from the high-pressure jet.
•
WARNING
. Do not use the machine near people if these are not wearing personal protective equipment.
•
WARNING
. Do not direct high-pressure jets against yourself or other people to clean clothes or footwear.
•
WARNING
. High-pressure jets can be hazardous if incorrectly used. High-pressure jets must not be directed
against people, energized electrical appliances or the machine itself.
•
WARNING
. Explosion risk - Do not spray inammable liquids.
• Do not use the machine under the rain.
• Read the
“CHECKING AND CONNECTING UP TO THE POWER SUPPLY”
paragraph carefully.
• Read the
“PRECAUTIONS CONCERNING PUMPED CHEMICAL PRODUCTS”
paragraph carefully.
• Do not remove the plug from the power socket by pulling the power lead.
• Keep the power lead, any extensions, the plugs and the sockets dry. Do not touch with wet hands.
• If the power lead is damaged, contact a
SKILLED TECHNICIAN
to have it replaced.
• Keep clear of moving parts of the machine, even if these are adequately protected.
• Do not remove the guards of the moving parts.
• Do not touch pipes containing liquids under pressure.
• Do not perform maintenance operations on the machine if this is operating.
• Read the
“INTENDED USE”
paragraph carefully.
• Do not modify in any way the installation conditions of the machine. In particular, do not modify the
fastening, the hydraulic connections and the guards.
• Do not operate any taps on the machine unless these are connected to an accessory that prevents the
To Next Page
Loading...
Need help?
General
