Crane BevMax 4 - Major Component Description; AC Distribution Box

30
“” key the display will show the current Golden
Eye setting on the top line and ‘“
”’ = XXX, where
XXX is the alternate setting either Drop or Home.
Press the “
” key to change to the alternate
setting.
Notes:
This mode only sets the operating condition of
Golden-Eye.
Selections are enabled/disabled in Mode 5-2.
SET GOLDEN-EYE SEL
This function is used to set up the Golden-Eye
Selections. To access this mode, press the Service
Switch 5 times, then press 2 on the selection keypad
the display will show “Set Golden-Eye Sel”. Press
the “
” key the display will show the selections
currently active for Golden Eye in the top line, if
necessary press the “
” key to see any
subsequent screens. If no selections are currently
enabled, the display will show “None Assigned”. The
factory default for Golden Eye is all selections
enabled. Press the “
” key the display will show
“Enter Start Location” use the selection keypad to
enter the selection number. Press the “
” key and
the display will show “Enter End Location”, use the
selection keypad to enter the ending location. See
notes below for further explanation.
Notes:
To Set Single Selections: Enter the same starting
and ending locations.
To Set Entire Shelves: In the Start Location
enter 2X”
” where X represents the shelf number.
The display will change to the ending location
screen with the last selection of that shelf already
displayed. Press “
” to set.
To Set Entire Machine: In the Start Location
enter 2 ”
” the display will change to show the
selection range of the machine in the top line and
“Continue? “
”=Y” in the bottom line. Press “”
to set.
To Set a Range of Selections: Enter the starting
selection number into the Start Location then enter
the last selection number into the End Location.
Press “
” to set. Rules: Single Selection, Range,
Shelf or Entire Machine
When enabling or disabling single selections the
opposite state of the current setting will be used. For
example: if you currently have selection 210 enabled
and you go into change it, it will change to disabled.
When enabling or disabling a range, shelf or the
entire machine. The setting will change to the
opposite of the lowest selection number in the
range, shelf or machine being set. For example if
you are changing the top shelf, and selection 210 is
set to enable while 212 -216 are set to disable, then
you would be disabling the top shelf from Golden-
Eye because the lowest selection number on the
shelf was set to enable.
CHECK MOTOR SCAN
This function is used to verify the state of the
selection motors in the Satellite (137 or 937
Satellite). To access this Mode, press the Service
Switch 5 times, then press 3 on the selection keypad
the display will show the results of the last Motor
Scan Test. Press the “
” key to scroll through the
results. To initiate a new scan of the motors Press
the 1 key. The display will say Scanning Motors
when
completed the display will say Scanning motors
done press “
” to continue. Press the “” key to
scroll through the results.
Set Credit Ret TO
This function is used to set the amount of time the
customer has to make another selection before their
change is returned. During this time period, the
customer can make a selection, add more money to
make another selection or press the coin return to
receive their change. To access this mode, press
the Service Switch 5 times, then press 4 on the
selection keypad the display will show “Set Credit
Ret TO”. Press the “
” key the display will show
“Set Credit Return” in the top line and “Timeout :
XX:XX in the bottom line, where XX:XX is the
currently set timeout. Use the numeric keypad to
enter the minutes and seconds. Press the “
” key
to lock in the change.
NOTE: The default time is 30 seconds.
Minimum time is 00:00
Maximum time is 05:00
Major Component Description
AC DISTRIBUTION BOX
BevMax 4 5800-4/3800-4
110 VAC units
Main Power Switch / Plug Interrupts hot side
of incoming power
to all components in
machine.
15 Amp Outlet (110 VAC) Provides power to
Refrigeration unit.
Transformer (T1) Provides 24 Volt
power to the
Controller Board.
DN5800-E4/3800-E4
220 VAC units
Main Power Switch / Plug Interrupts hot side
of incoming power
to all components in
machine.
Receptacle, Panel Mount Provides power to
IEC 320 (220 VAC) Refrigeration unit.