Datakom D Series - Phase, 4 Wire, Star; Phase, 3 Wire, Delta

138 pages

To Next Page

To Previous Page

D-500L Firmware V-5.8

K35D03-EN - 30 -

4.3. 3 PHASE, 3 WIRE, DELTA

4.2. 3 PHASE, 4 WIRE, STAR

Main Page

Table of Contents6
Installation Instructions10
Mounting11
Dimensions11
Sealing, Gasket14
Electrical Installation15
Terminal Descriptions16
Battery Voltage Input16
Ac Voltage Inputs17
Ac Current Inputs18
Digital Inputs21
Analog Sender Inputs and Sender Ground21
Charge Input Terminal22
Magnetic Pickup Input22
Mains Contactor Output23
Generator Contactor Output23
Digital Outputs23
Input/Output Extension24
Port25
J1939-Canbus Port25
Usb Device Port26
Gsm Modem (Optional)27
Topologies29
Selecting the Topology29
Phase, 4 Wire, Star30
Phase, 3 Wire, Delta30
Phase, 4 Wire, Delta31
Phase, 3 Wire, Delta, 2 Ct (L1-L2)31
Phase, 3 Wire, Delta, 2 Ct (L1-L3)32
PHASE, 3 WIRE, DELTA, 2 Cts (L1-L2)32
PHASE, 3 WIRE, DELTA, 2 Cts (L1-L3)33
Phase, 2 Wire33
Functionalities34
Ct Location Selection34
Amf Functionality34
Ats Functionality34
Remote Start Functionality34
Engine Controller Functionality35
Remote Display Unit Functionality36
400Hz Operation36
Connection Diagrams37
AMF FUNCTIONALITY, Cts at LOAD SIDE37
AMF FUNCTIONALITY, Cts at ALTERNATOR SIDE38
Ats Functionality39
Remote Start Functionality40
Engine Control Functionality41
Remote Display Panel Functionality42
Terminal Description43
Technical Specifications46
Description of Controls47
Front Panel Functionality47
Pushbutton Functions48
Display Screen Organization49
Automatic Display Scroll50
Measured Parameters51
Led Lamps52
Waveform Display & Harmonic Analysis53
Displaying Event Logs55
Statistical Counters57
Fuel Filling Counter57
Fuel Consumption Monitoring58
Operation of the Unit59
Quick Start Guide59
Stop Mode59
Auto Mode60
Run Mode, Manual Control61
Test Mode61
Protections and Alarms62
Disabling All Protections63
Service Request Alarm63
Shutdown Alarms64
Loaddump Alarms65
Warnings66
Non-Visual Warnings68
Programming69
Resetting to Factory Defaults69
Entering the Programming Mode70
Navigating between Menus71
Modifying Parameter Value72
Programming Mode Exit73
Program Parameter List74
Controller Configuration Group74
Electrical Parameters Group80
Engine Parameters Group87
Adjust Date and Time94
Weekly Operation Schedule94
Exerciser Schedule95
Sender Configuration96
Digital Input Configuration98
Output Configuration100
Site ID String102
Engine Serial Number102
Modem1-2/Sms1-2-3-4 Telephone Numbers102
Gsm Modem Parameters103
Ethernet Parameters104
Crank Cutting105
Overcurrent Protection (Idmt)106
Motorized Circuit Breaker Control108
J1939 Canbus Engine Support110
Gps Support114
Gsm Configuration116
Central Monitoring of Gensets116
E-Mail Sending116
Sms Commands117
Software Features119
Load Shedding / Dummy Load119
Load Add / Substract120
Five Step Load Management121
Remote Start Operation122
Disable Auto Start, Simulate Mains122
Battery Charging Operation, Delayed Simulate Mains123
Dual Genset Mutual Standby Operation124
Multiple Voltage and Frequency125
Single Phase Operation125
External Control of the Unit125
Automatic Exerciser126
Weekly Operation Scheduler126
Engine Heating Operation127
Engine Idle Speed Operati̇on127
Engine Block Heater127
Fuel Pump Control128
Gas Engine Fuel Solenoid Control128
Pre-Transfer Signal128
Charging the Engine Battery129
Externally Controlled Digital Outputs129
Combat Mode129
Resetting the Controller130
Automatic Connection Topology Determination130
Zero Power at Rest131
Modbus Communications132
Parameters Required for Rs-485 Modbus Operation133
Data Formats133
Declaration of Conformity136
Maintenance136
Disposal of the Unit136
Rohs Compliance136
Troubleshooting Guide137

Datakom D Series - Phase, 4 Wire, Star; Phase, 3 Wire, Delta

Table of Contents

Related product manuals