EasyManua.ls Logo

DCS 900E - User Manual

DCS 900E
67 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
© 1994, 1996, 2000 dCS Ltd
All rights reserved. Reproduction of this manual in any manner whatsoever,
without the written permission of dCS
1
is strictly forbidden. Additional copies of
this manual may be obtained from dCS.
Information contained in this manual is subject to change without notice, and
whilst it is checked for accuracy, no liabilities can be accepted for errors.
1
dCS Ltd is Data Conversion Systems Ltd. Company registered in the England no. 2072115
dCS 900E / 902E
Analogue to Digital Converter
User Manual
Software versions 1.3x to 1.5x
12
th
June 2000
All manuals and user guides at all-guides.com
all-guides.com

Table of Contents

Questions and Answers

  • K
    Kristy SpearsSep 10, 2025
    How to troubleshoot a DCS Media Converter that fails to power up?
    • L
      Lindsey MartinSep 10, 2025
      If your DCS Media Converter fails to power up, take these steps: * Ensure the mains cable is securely connected and the unit's mains switch is On. * Verify the rated supply voltage on the unit's rear panel matches your local supply voltage. * Check the fuse; if it's blown, identify and fix the cause before replacing it. * Make sure the mains cable is fully inserted into the mains inlet at the rear of the unit.
  • K
    Kevin FosterAug 23, 2025
    What to do if one output channel is low or absent on my DCS 900E Media Converter?
    • J
      Joshua ChavezAug 23, 2025
      Ensure that all cables are connected correctly and are not damaged. Verify that the balance is not offset elsewhere in the system. If the level trimmers on the rear panel have been adjusted, check that one has not been set much lower than the other.
  • B
    Brittany KerrAug 25, 2025
    Why won't the level trimmers on the rear panel of my DCS Media Converter change the input level?
    • G
      garciasandraAug 25, 2025
      Ensure the trim tool or screwdriver you are using is narrow enough to reach the adjuster (about 2.5mm or 0.1” diameter) and long enough (at least 12mm or 0.5”). The trimmer may be at the end of its travel - try turning it several times the other way. It is a 20-turn device.
  • C
    Crystal RiveraAug 27, 2025
    What to do if the audio output is low or absent on my DCS Media Converter?
    • K
      Katelyn BrownAug 27, 2025
      If the audio output from your DCS Media Converter is low or absent: * Check all cables for correct connection and damage, as damaged cables are a very common cause of malfunctions. * Ensure both the source and destination equipment are powered on and configured correctly. * Verify that an audio signal is present on at least one of the inputs. * Make sure that the Mute function is not enabled (LED off).
  • Z
    Zachary McdonaldAug 27, 2025
    How do I fix a DCS Media Converter when one output channel is low or absent?
    • B
      brandon37Aug 28, 2025
      If one output channel on your DCS Media Converter has low or no audio: * Check that all cables are connected correctly and are not damaged, as damaged cables are a very common source of malfunctions. * Check that the balance isn't offset elsewhere in the system. * If the level trimmers on the rear panel have been adjusted, ensure that one hasn't been set much lower than the other.
  • A
    Angela HarrisAug 29, 2025
    Why don't the level trimmers change the input level on my DCS Media Converter?
    • A
      Alan JacksonAug 29, 2025
      If the level trimmers on the rear panel of your DCS Media Converter aren't changing the input level: * Make sure the trim tool or screwdriver you're using is narrow enough (about 2.5mm or 0.1” diameter) and long enough (at least 12mm or 0.5”) to reach the adjuster. * The trimmer might be at the end of its travel; try turning it several times in the opposite direction. It's a 20-turn device.
  • J
    James SantiagoSep 18, 2025
    Why does my DCS 900/902 Media Converter show overload when the external meter doesn't?
    • A
      Aaron HoSep 18, 2025
      The dCS 900 / 902 monitors internal points and data word values to calculate overload. This may lead it to indicate an overload even if the final external data word doesn't show it. For example, it could be due to a very narrow but large spike. Some digital meters are quite insensitive to overloads. If the dCS 900 / 902 indicates an overload, it is likely accurate. You have the option to disregard it.
  • S
    Shawn WardSep 22, 2025
    Why does my DCS Media Converter slave to Word Clock but not AES/EBU?
    • M
      Mrs. Mary SantiagoSep 22, 2025
      This can be caused by erroneous system messages. Contact your dealer or dCS for advice.
  • L
    lmartinezSep 7, 2025
    What to do if the DCS 900E Media Converter unit fails to slave to a Master Clock?
    • B
      Becky Beard MDSep 7, 2025
      Press the Master/Slave button to select the appropriate mode. If a suitable reference is connected, the LED should light and the unit should lock after a few seconds. Check that the Reference In or Clk In cable is connected correctly and is not damaged. Verify that the Master Clock is switched on, set to the correct sample rate, and doesn't need recalibration. You can connect a different piece of digital equipment to test the locking capability of the unit. If the condition persists, contact your Distributor or dCS.
  • J
    Joseph SmithSep 4, 2025
    How to fix periodic clicks in the recording with DCS 900E Media Converter?
    • S
      sparkscarmenSep 4, 2025
      If you are using a Master Clock, check that the ADC AND the recorder are synced to it.

DCS 900E Specifications

General IconGeneral
Fiber CableMulti-mode or Single-mode
StandardsIEEE 802.3
ModelDCS-900E
LED IndicatorsPower
Power5V DC, 1A
Operating Temperature0°C to 50°C
Storage Temperature-20°C to 70°C
InterfaceRJ-45, SFP
Fiber TypeMulti-mode / Single-mode
WavelengthDepends on SFP transceiver

Related product manuals