Getting Started Connections Setup Playback Remote Control Multi-Zone Information
ENGLISH
Symptom Cause Countermeasure Page
No sound is
produced from
center speaker.
• Monaural source (monitor, AM
station, etc.) being played in
“STANDARD” mode.
• The mode is set to something
other than “STANDARD”.
43, 44
No sound
is produced
from surround
speakers.
• The surround mode is set to
“STEREO”, “DIRECT” or “PURE
DIRECT”.
• The surround speaker’s power
amplifier is assigned to a different
channel.
• Set to a surround playback
mode.
• Check the setting and change it
as necessary.
43, 44
36
No sound is
produced from
surround back
speaker.
• Surround back speaker setting is
set to “None”.
• Surround mode not set to a mode
for 6.1- or 7.1-channel playback.
• The surround back speaker’s
power amplifier is assigned to a
different channel.
• Set to something other than
“None”.
• Select a surround playback
mode.
• Check the setting and change it
as necessary.
29
43, 44
36
No sound is
produced from
subwoofer.
• Subwoofer’s power not turned
on.
• The “Subwoofer” setting at
“Speaker configuration” is set to
“No”.
• The subwoofer is not properly
connected.
• The subwoofer’s volume is
turned off.
• Turn on the subwoofer’s power.
• Set to “Yes”.
• Check the connections.
• Adjust the subwoofer’s volume
to an appropriate level.
–
29
10
63
No test tones are
produced when
main remote
control unit’s TEST
TONE button is
pressed.
• Surround mode not set to
“STANDARD”.
• Set to the “STANDARD” mode. 43
DTS sound is not
output.
• DVD player’s audio output setting
is not set to bitstream.
• DVD player is not compatible
with DTS sound playback.
• The AVR-4308’s “Decode Mode”
setting is set to “PCM”.
• Set the DVD player. For details,
refer to the DVD player’s
operating instructions.
• Use a DTS-compatible player.
• Set to the “Auto” or “DTS”
mode.
–
–
40
HDMI audio
signals are not
output from
speakers.
• The “Manual Setup” – “HDMI
Setup” – “Audio” setting is set to
“TV”.
• Set to “Amp”. 31
Symptom Cause Countermeasure Page
No sound is
output from
the monitor
connected
with HDMI
connections.
• The “Manual Setup” – “HDMI
Setup” – “Audio” setting is set to
“Amp”.
• Set to “TV”. 31
GAudioH
Symptom Cause Countermeasure Page
The on-screen
display does not
appear.
• The format of the GUI and TV
(PAL or NTSC) do not match.
• Match the format of the GUI and
TV.
36
No picture
appears.
• The connections between the
AVR-4308 and monitor are
faulty.
• The monitor’s input setting is
wrong.
• PURE DIRECT mode is set.
• The player is connected using the
component input connectors, the
monitor is connected using the
video (yellow) or S-Video output
connectors.
• Check the connections.
• Set properly.
• Cancel the PURE DIRECT mode.
• High definition (1080i/720p) and
progressive (480p/576p) video
signals are not down-converted.
Set the player to interlace
(480i/576i) signals.
12 ~ 23
–
43, 44
–
No picture
appears
with HDMI
connections.
• The connections to the HDMI
connectors are faulty.
• HDMI input setting is improper.
• The monitor is not compatible
with copyright protection
(HDCP).
• The HDMI format of the player
and monitor do not match.
• Check the connections.
• Check the HDMI input setting.
• Connect a monitor that is
compatible with copyright
protection (HDCP).
• Match the HDMI format of the
player and monitor.
12
41
12
12
Picture cannot be
recorded.
• Input source does not match
recorder’s video connection
connector (video or S-Video).
• The video conversion function
does not work for the REC
OUT connectors. Match the
input source and recorder
connections.
16
DVDs cannot be
copied on a VCR.
–
• This is not a malfunction. Most
movie software includes copy
prevention signals and cannot be
copied.
–
GVideoH
Troubleshooting
To Next Page
Loading...
Need help?
General
