105
Basic versionSimple version Information
ENGLISH
Advanced version
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu
MANUAL SETUP
Setting items Setting details
GUI
(Continued)
TUNER : Set the tuner screen display time when the input source is
“SIRIUS” or “HD Radio”.
• 30s : Show display for 30 seconds after operation.
• 10s : Show display for 10 seconds after operation.
• OFF : Turn display off.
• Always : Show display continuously.
Remote Preset Codes
Search a preset code to
register in the remote
control unit.
See “Registering preset codes” (vpage108).
Quick Select Name
Change the “Quick Select”
display title to one you
prefer.
• Up to 16 characters can be input.
• For character input, see page 78.
Zone Rename
Change the display title of
each zone to one you prefer.
• Up to 10 characters can be input.
• For character input, see page 78.
Trigger Out 1 /
Trigger Out 2
Select the condition for
activating Trigger Out 1/2 for
the input source, surround
mode, etc.
See “TRIGGER OUT jacks”
(vpage27) for more
information on trigger out.
Trigger Out 1/2
n When setting for zone (MAIN ZONE / ZONE2 / ZONE3)
Trigger out is activated through linkage to the power of the zone set
to “ON”.
n When setting for input source
Activate trigger out when the input source set to “ON” is selected.
Active for the zone set to “ON” with “When setting for zone”.
n When setting for surround mode
Activate trigger out when the surround mode set to “ON” is selected.
Active when the “MAIN ZONE” set to “ON” with “When setting
for zone” is selected, and when the input source set to “ON” with
“When setting for input source” is selected.
n When setting for HDMI monitor
Activate trigger out when the HDMI monitor set to “ON” is selected.
Activate trigger out when the HDMI monitor set to “ON” is
selected. Active when the “MAIN ZONE” set to “ON” with
“When setting for zone” is selected, and when the input source
set to “ON” with “When setting for input source” is selected.
n When setting for “Vertical Stretch”
Activate trigger out through linkage when “Vertical Stretch” (vpage98)
is set to “ON”.
• ON : Activate trigger on this mode.
• – – – : Do not activate trigger on this mode.
Setting items Setting details
Remote ID
Set when you operate
another DENON AV
amplifier with the remote
control unit of this unit.
Match the remote control
unit you are using with the
remote ID of this unit.
1 / 2 / 3 / 4
NOTE
When changing the remote ID, also change the remote ID of main remote
control unit (RC-1145) at the same time. Also change the sub remote
control unit (RC-1148) at the same time.
Dimmer
Adjust the display
brightness of this unit.
Bright : Normal display brightness.
Dim : Reduced display brightness.
Dark : Very low display brightness.
OFF : Turns the display off.
Setup Lock
Protect settings from
inadvertent change.
ON : Turn protection on.
OFF : Turn protection off.
When canceling the setting, set “Setup Lock” to “OFF”.
NOTE
When “Setup Lock” is set to “ON”, the settings listed below can no
longer be changed. Also, “SETUP LOCKED!” is displayed if you attempt
to operate related settings.
• Menu operations • Channel Level
• RESTORER • MultEQ
®
XT 32
• Dolby Volume • Dynamic EQ
®
• Dynamic Volume
®
Maintenance Mode
Use when receiving
maintenance from a DENON
service engineer or custom
installer.
NOTE
Only use this function if so instructed by a DENON serviceperson or
installer.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
