What to do if the Denon AVR-A100 power indicator blinks red after turning it on?
If, after turning on the power, the power indicator blinks red in intervals of approximately 0.5 seconds, the unit's amplifier circuit has likely failed. Turn off the power and contact a DENON service advisor.
Why is there no sound from subwoofer on my Denon AVR-A100 Receiver?
If you're not getting any sound from the subwoofer connected to your Denon Receiver, first check the subwoofer connections and ensure the subwoofer is powered on. Then, in the menu, set “Speaker Config.” – “Subwoofer” to either “1spkr” or “2spkrs”. Also, if “Front” and “Center” for “Speaker Config.” are set to “Large” and “Subwoofer Mode” is set to “LFE”, no sound may be output depending on the input signal or selected surround mode.
How to fix a Denon AVR-A100 when the power does not turn on?
First, check that the power plug is correctly inserted into the power outlet. If it still doesn't work, the protection circuit might be active. Disconnect the power plug from the electric outlet, wait 5 to 10 seconds, and then re-insert it.
What does it mean when the power indicator is blinking red on my Denon AVR-A100?
A blinking red power indicator, with intervals of approximately 0.5 seconds, suggests there may be an issue with the speakers. Ensure you are using speakers with the specified impedance. Also, check the speaker cable for shorts (touching wires). If a short exists, firmly twist the core wire in the speaker cable and reconnect it to the speaker terminal.
What to do if my Denon AVR-A100 Receiver power does not turn on?
If your Denon Receiver isn't powering on, ensure the power plug is correctly inserted into the outlet. If that doesn't work, the protection circuit may be active. Disconnect the power plug, wait 5 to 10 seconds, and then reinsert it.
How to enable DTS sound output on my Denon AVR-A100 Receiver?
To enable DTS sound output on your Denon Receiver, set “Decode Mode” on the menu to either “Auto” or “DTS”.
What to do if no picture appears on Denon Receiver?
If no picture appears on your Denon Receiver, check the TV connection and ensure the TV input is set correctly.
Why I cannot play Internet radio on my Denon AVR-A100 Receiver?
If you're unable to play Internet radio on your Denon Receiver, ensure the Ethernet cable is properly connected and that your network is connected. Only MP3 and WMA Internet radio programs can be played on this unit. Check your computer's or router's firewall settings, as they may be activated. The radio station might not be currently broadcasting, so choose one that is. Finally, verify the set’s IP address is correct.
How to fix no video output with HDMI connection on Denon AVR-A100?
If you're experiencing no video output with an HDMI connection on your Denon Receiver, first check the HDMI cable connections. Ensure the input source matches the connected HDMI port. Also, verify that your TV is compatible with HDCP copyright protection, as incompatible devices can prevent correct video output.
How do I get sound from the front height speaker on my Denon Receiver?
To get sound from the front height speaker, set “Surround Parameters” – “PLgz Height” on the menu to “ON。”
General| Impedance | 4 Ω |
|---|---|
| Sensitivity | 102 dB |
| Output level | 150 mV |
| Receiver type | Surround |
| Frequency range | 10 - 100000 Hz |
| Input sensitivity | 200 mV |
| Audio output channels | 9.2 channels |
| Total Harmonic Distortion (THD) | 0.05 % |
| Dynamic power per channel (4 Ohm) | 220 W |
| Dynamic power per channel (8 Ohm) | 150 W |
| Power output per channel (1KHz@6 Ohm) | 170 W |
| Power output per channel (20-20KHz@8 Ohm) | 140 W |
| HDMI in | 7 |
| Audio (L/R) in | 9 |
| Composite video in | 5 |
| Digital audio optical in | 2 |
| Ethernet LAN (RJ-45) ports | 1 |
| Component video (YPbPr/YCbCr) in | 3 |
| AirPlay | Yes |
| Display | - |
| HDMI version | 1.4a |
| Product color | Black |
| Audio decoders | DTS-HD, Dolby TrueHD |
| Handheld remote control | No |
| Apple docking compatibility | Not supported |
| AC input voltage | 120 V |
| AC input frequency | 60 Hz |
| Power consumption (standby) | 0.1 W |
| Power consumption (typical) | 780 W |
| Connectivity technology | Wired |
| Speakers connectivity type | RCA |
| Audio (L/R) out | 11 |
| AM band range | 520 - 1710 kHz |
| FM band range | 87.5 - 107.9 MHz |
| Supported radio bands | AM, FM |
| Internet radio services supported | SIRIUS Internet Radio |
Weight and Dimensions| Depth | 414 mm |
|---|---|
| Width | 434 mm |
| Height | 171 mm |
| Weight | 18500 g |
To Next Page
