Why is my Denon AVR-A100 power indicator blinking red in intervals of approximately 2 seconds?
If the power indicator on your Denon Receiver is blinking red in intervals of approximately 2 seconds, the unit's internal temperature has risen. Turn off the power and allow the unit to cool down before reapplying power. Also, reinstall the unit in a location with better ventilation.
How do I get sound from the front height speaker on my Denon Receiver?
To get sound from the front height speaker, set “Surround Parameters” – “PLgz Height” on the menu to “ON。”
Why is there no sound from the surround back speaker on my Denon Receiver?
If there's no sound from the surround back speaker, check the following settings: 1. Ensure “Amp Assign” is correctly set to output audio from the surround back speakers. 2. Verify that “Speaker Config.” – “Surround Back” is set to something other than “None” in the menu. 3. Confirm that “Surround Parameters” – “Surround Back” is not set to “OFF” in the menu. 4. Make sure the surround mode is set to something other than “STEREO”.
What to do if audio is not outputting from my Denon Receiver?
If you're not getting any sound from your Denon Receiver, try these steps: * Check all device connections. * Verify the speaker connections and configurations. * Ensure the audio device is powered on. * Adjust the master volume. * Cancel mute mode. * Select the correct input source and mode. * Disconnect any connected headphones.
Why is there no sound from front height speaker on my Denon AVR-A100 Receiver?
If there's no sound coming from the front height speaker on your Denon Receiver, make sure “Surround Parameters” – “PLgz Height” is set to “ON” in the menu. Also, check that “Amp Assign” is correctly configured to output audio from the front height speakers and that “Speaker Config.” – “Front Height” isn't set to “None”.
Why is there no sound from surround back speaker on my Denon AVR-A100 Receiver?
If you're not getting any sound from the surround back speaker of your Denon Receiver, check that “Amp Assign” is set correctly to output audio from those speakers. Also, in the menu, ensure “Speaker Config.” – “Surround Back” is not set to “None”, and “Surround Parameters” – “Surround Back” is not set to “OFF”. Finally, make sure the surround mode isn't set to “STEREO”.
What to do if my Denon AVR-A100 Receiver power does not turn on?
If your Denon Receiver isn't powering on, ensure the power plug is correctly inserted into the outlet. If that doesn't work, the protection circuit may be active. Disconnect the power plug, wait 5 to 10 seconds, and then reinsert it.
What does it mean when the power indicator is blinking red on my Denon AVR-A100?
A blinking red power indicator, with intervals of approximately 0.5 seconds, suggests there may be an issue with the speakers. Ensure you are using speakers with the specified impedance. Also, check the speaker cable for shorts (touching wires). If a short exists, firmly twist the core wire in the speaker cable and reconnect it to the speaker terminal.
How to fix a Denon AVR-A100 when the power does not turn on?
First, check that the power plug is correctly inserted into the power outlet. If it still doesn't work, the protection circuit might be active. Disconnect the power plug from the electric outlet, wait 5 to 10 seconds, and then re-insert it.
Why is there no sound from subwoofer on my Denon AVR-A100 Receiver?
If you're not getting any sound from the subwoofer connected to your Denon Receiver, first check the subwoofer connections and ensure the subwoofer is powered on. Then, in the menu, set “Speaker Config.” – “Subwoofer” to either “1spkr” or “2spkrs”. Also, if “Front” and “Center” for “Speaker Config.” are set to “Large” and “Subwoofer Mode” is set to “LFE”, no sound may be output depending on the input signal or selected surround mode.
General| Impedance | 4 Ω |
|---|---|
| Sensitivity | 102 dB |
| Output level | 150 mV |
| Receiver type | Surround |
| Frequency range | 10 - 100000 Hz |
| Input sensitivity | 200 mV |
| Audio output channels | 9.2 channels |
| Total Harmonic Distortion (THD) | 0.05 % |
| Dynamic power per channel (4 Ohm) | 220 W |
| Dynamic power per channel (8 Ohm) | 150 W |
| Power output per channel (1KHz@6 Ohm) | 170 W |
| Power output per channel (20-20KHz@8 Ohm) | 140 W |
| HDMI in | 7 |
| Audio (L/R) in | 9 |
| Composite video in | 5 |
| Digital audio optical in | 2 |
| Ethernet LAN (RJ-45) ports | 1 |
| Component video (YPbPr/YCbCr) in | 3 |
| AirPlay | Yes |
| Display | - |
| HDMI version | 1.4a |
| Product color | Black |
| Audio decoders | DTS-HD, Dolby TrueHD |
| Handheld remote control | No |
| Apple docking compatibility | Not supported |
| AC input voltage | 120 V |
| AC input frequency | 60 Hz |
| Power consumption (standby) | 0.1 W |
| Power consumption (typical) | 780 W |
| Connectivity technology | Wired |
| Speakers connectivity type | RCA |
| Audio (L/R) out | 11 |
| AM band range | 520 - 1710 kHz |
| FM band range | 87.5 - 107.9 MHz |
| Supported radio bands | AM, FM |
| Internet radio services supported | SIRIUS Internet Radio |
Weight and Dimensions| Depth | 414 mm |
|---|---|
| Width | 434 mm |
| Height | 171 mm |
| Weight | 18500 g |
To Next Page
