Denon AVR-A100 User Manual

114
ENGLISH
Operating the main remote control unit
n Using the macro function
1
3UHVVMACRO
2
3UHVVWKHQUICK SELECTEXWWRQ
\RXXVHGWRVWRUHWKHPDFUR
IXQFWLRQ
Button Macro number
QUICK SELECT 1 MACRO-1
QUICK SELECT 2 MACRO-2
QUICK SELECT 3 MACRO-3
n Resetting the macro function
1
3UHVV DQG KROG POWER ON DQG
ZONE/DEVICE ON IRU DW OHDVW 
VHFRQGV
“SETUP” flashes twice on the remote
control unit.
2
8VHuiWRGLVSOD\³5(6(7´RQ
WKHUHPRWHFRQWUROXQLWDQGSUHVV
ENTER
3
8VHuiWRGLVSOD\³0$&52´
RQWKHUHPRWHFRQWUROXQLWDQG
SUHVV
ENTER
4
:KHQ³0&1R"´DSSHDUVRQWKH
UHPRWH FRQWURO XQLW SUHVV WKH
QUICK SELECT EXWWRQ WKDW \RX
ZDQWWRUHVHW
“RESET” flashes four times on the
remote control unit and the normal
operation mode is restored.
Button Macro number
QUICK SELECT 1 MACRO-1
QUICK SELECT 2 MACRO-2
QUICK SELECT 3 MACRO-3
Specifying the zone used with the main
remote control unit
When the ZONE SELECT button is pressed, only the set zone can be
operated with the remote control unit.
• The factory setting is “M234”.
1
3UHVV DQG KROG POWER ON DQG
ZONE/DEVICE ON IRU DW OHDVW 
VHFRQGV
“SETUP” flashes twice on the remote
control unit.
2
8VHuiWRGLVSOD\³=21(/´RQ
WKHUHPRWHFRQWUROXQLWDQGSUHVV
ENTER
3
8VHuiWRVHWWKH]RQHWREHXVHG
DQGSUHVV
ENTER
“SET” flashes four times on the remote
control unit and the normal operation
mode is restored.
Remote control unit
display
Zone to be used
M MAIN ZONE only
M2
MAIN ZONE /
ZONE2
M23
MAIN ZONE /
ZONE2 /
ZONE3
M234
MAIN ZONE /
ZONE2 /
ZONE3 /
ZONE4
Setting the Remote ID
When using multiple DENON AV receivers in the same room, make
this setting so that only the desired AV receiver operates.
• The factory setting is “ID-1”.
1
3UHVV DQG KROG POWER ONDQG
ZONE/DEVICE ON IRU DW OHDVW 
VHFRQGV
“SETUP” flashes twice on the remote
control unit.
2
8VH ui WR GLVSOD\ ³5&,'´ RQ
WKHUHPRWHFRQWUROXQLWDQGSUHVV
ENTER
3
8VHuiWRVHWWKHUHPRWH,'DQG
SUHVV
ENTER
“SET” flashes four times on the remote
control unit and the normal operation
mode is restored.
Remote control unit
display
Remote ID
ID-1 1
ID-2 2
ID-3 3
ID-4 4
NOTE
When you change the remote ID, make sure that the remote
control unit and the remote ID of the main unit are exactly the same
(vpage105).

Denon AVR-A100 Specifications

General

Impedance	4 Ω
Sensitivity	102 dB
Output level	150 mV
Receiver type	Surround
Frequency range	10 - 100000 Hz
Input sensitivity	200 mV
Audio output channels	9.2 channels
Total Harmonic Distortion (THD)	0.05 %
Dynamic power per channel (4 Ohm)	220 W
Dynamic power per channel (8 Ohm)	150 W
Power output per channel (1KHz@6 Ohm)	170 W
Power output per channel (20-20KHz@8 Ohm)	140 W
HDMI in	7
Audio (L/R) in	9
Composite video in	5
Digital audio optical in	2
Ethernet LAN (RJ-45) ports	1
Component video (YPbPr/YCbCr) in	3
AirPlay	Yes
Display	-
HDMI version	1.4a
Product color	Black
Audio decoders	DTS-HD, Dolby TrueHD
Handheld remote control	No
Apple docking compatibility	Not supported
AC input voltage	120 V
AC input frequency	60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	780 W
Connectivity technology	Wired
Speakers connectivity type	RCA
Audio (L/R) out	11
AM band range	520 - 1710 kHz
FM band range	87.5 - 107.9 MHz
Supported radio bands	AM, FM
Internet radio services supported	SIRIUS Internet Radio

Weight and Dimensions

Depth	414 mm
Width	434 mm
Height	171 mm
Weight	18500 g