Denon AVR-A100 User Manual

129
Basic versionSimple version Advanced version
ENGLISH
Information
Surround
n Types of input signals, and corresponding surround modes
This table shows the input signal that can be played in each surround mode. Check the audio signal of the input source then select the surround mode.
Symbols in the table
F This indicates the default surround mode.
D This indicates the surround mode that is fixed when “AFDM” (vpage87) is set to “ON”.
S This indicates the selectable surround mode.
Surround mode (vpage50)
NOTE
Input signal types and formats
ANALOG
PCM
(multi ch)
PCM
(2ch)
WMA/
MP3/
MPEG-4
AAC/FLAC/
WAV
DTS-HD
DTS-HD
LBR
DTS DOLBY DOLBY DIGITAL Super Audio CD
DTS-HD
Master
Audio
DTS-HD
High
Resolution
Audio
DTS
EXPRESS
DTS ES
DSCRT
(With Flag)
DTS ES
MTRX
(With Flag)
DTS
(5.1ch)
DTS 96/24
DOLBY
TrueHD
DOLBY
DIGITAL
Plus
DOLBY
DIGITAL EX
(With Flag)
DOLBY
DIGITAL EX
(With no
Flag)
DOLBY
DIGITAL
(5.1ch)
DOLBY
DIGITAL
(2ch)
DSD
(multi ch)
DSD
(2ch)
DTS SURROUND
DTS-HD MSTR
z4 F
DTS-HD HI RES
z4 F
DTS ES DSCRT6.1
z1z4 F D
DTS ES MTRX6.1
z1z4 F D
DTS SURROUND
z4 SSF
DTS 96/24
z4 F
DTS (–HD) + PLgx CINEMA z2z4 SSSS S SS
DTS (–HD) + PLgx MUSIC z1z4 SSS
S S SS
DTS (–HD) + PLgz z3 SSS S S S S
DTS EXPRESS
z4 F
DTS (–HD) + NEO:6
z1z4 SSS S SS
DTS NEO:6 CINEMA
z5 SSS SS
DTS NEO:6 MUSIC
z5 SSS SS
DTS NEO:6 CINEMA A-DSX
z6 SSS SS
DTS NEO:6 MUSIC A-DSX
z6 SSS SS
Audyssey DSX
z6 SSSS S SS
DOLBY SURROUND
DOLBY TrueHD
z4 F
DOLBY DIGITAL+
z4 F
DOLBY DIGITAL EX
z1z4 SSS
DOLBY (D+) (HD) +EX
z1z4 SS
DOLBY DIGITAL
z4 SFF
DOLBY (D) (D+) (HD) +PLgx
CINEMA
z2z4 SSF DS S
DOLBY (D) (D+) (HD) +PLgx
MUSIC
z1z4 SSSSS
DOLBY (D) (D+) (HD) +PLgz z3 SSSSS
DOLBY PRO LOGIC gx CINEMA z1 SS
S SS
DOLBY PRO LOGIC gx MUSIC z1 SSS SS
DOLBY PRO LOGIC gx GAME z1 SSS SS
DOLBY PRO LOGIC gz z3 SSS SS
z1 If “Speaker Config.” – “Surround Back” (vpage96) is set to “None”, this surround mode cannot be selected.
z2 If “Speaker Config.” – “Surround Back” (vpage96) is set to “1 spkr” or “None”, this surround mode cannot
be selected.
z3 If “Speaker Config.” – “Front Height” (vpage96) is set to “None”, this surround mode cannot be selected.
z4 The same was when “Audyssey DSX™” (vpage90) setting is set to “ON”.
z5 If “Speaker Config.” – “Center” and “Surround” is set to “None” or headphones are used, this surround mode cannot
be selected.
z6 If “Speaker Config.” – “Front Height”, “Front Wide” and “Center” is set to “None” or headphones are used, this
surround mode cannot be selected.

Denon AVR-A100 Specifications

General

Impedance	4 Ω
Sensitivity	102 dB
Output level	150 mV
Receiver type	Surround
Frequency range	10 - 100000 Hz
Input sensitivity	200 mV
Audio output channels	9.2 channels
Total Harmonic Distortion (THD)	0.05 %
Dynamic power per channel (4 Ohm)	220 W
Dynamic power per channel (8 Ohm)	150 W
Power output per channel (1KHz@6 Ohm)	170 W
Power output per channel (20-20KHz@8 Ohm)	140 W
HDMI in	7
Audio (L/R) in	9
Composite video in	5
Digital audio optical in	2
Ethernet LAN (RJ-45) ports	1
Component video (YPbPr/YCbCr) in	3
AirPlay	Yes
Display	-
HDMI version	1.4a
Product color	Black
Audio decoders	DTS-HD, Dolby TrueHD
Handheld remote control	No
Apple docking compatibility	Not supported
AC input voltage	120 V
AC input frequency	60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	780 W
Connectivity technology	Wired
Speakers connectivity type	RCA
Audio (L/R) out	11
AM band range	520 - 1710 kHz
FM band range	87.5 - 107.9 MHz
Supported radio bands	AM, FM
Internet radio services supported	SIRIUS Internet Radio

Weight and Dimensions

Depth	414 mm
Width	434 mm
Height	171 mm
Weight	18500 g