136
ENGLISH
GHDMIH
Symptom Cause/Solution Page
No audio is
output with HDMI
connection.
•
Check the connection of the HDMI connectors.
• When outputting HDMI audio from the speakers, set “HDMI
Audio Out” on the menu to “AMP”.
• When outputting HDMI audio from a TV, set “HDMI Audio Out”
on the menu to “TV”.
17
98
98
No video is
output with HDMI
connection.
• Check the connection of the HDMI connectors.
• Set the input source to match the connected HDMI connector.
• Check whether the TV is compatible with copyright protection
(HDCP). If connected to a device not compatible with HDCP, video
will not be output correctly.
17
17, 28
16
When the following
operations are
performed on
devices compatible
with HDMI control,
the same operations
occur on this unit.
• Power ON/OFF
• Switching audio
output devices
• Adjust volume
• Switch input source
• Set “HDMI Control” on the menu to “OFF”. To operate power
only for each device, set “Power Off Control” to “OFF”.
65, 99
GSIRIUS Satellite RadioH
Symptom Cause/Solution Page
“CHECK SIRIUS
TUNER” is displayed.
•
The SiriusConnect Home Tuner unit is not connected. Check that
the connections are correct.
23
”ANTENNA ERROR”
is displayed.
• The antenna is not connected. Check that the connections are
correct.
23
”NO SIGNAL” is
displayed.
• The antenna is not connected. Check that the connections are
correct.
–
”INVALID
CHANNEL” is
displayed.
• Channel is not present. Select another channel. –
”ACQUIRING
SIGNAL” is
displayed.
• The signal cannot be received. Reposition your SiriusConnect
Home Tuner and Home Dock antenna.
• Displays while SiriusConnect Home Tuner is connected. Reposition
your SiriusConnect Home Tuner and Home Dock antenna.
–
–
”Call SIRIUS”
z
is
displayed.
• Channels are not subscribed to. If you subscribe to the channel,
you can receive the channel.
–
”SUBSCRIPTION
UPDATED” is
displayed.
• While updating contract information. –
”Enter Lock Code
[ ]” is displayed.
• Selected channels are locked. Please insert pass word (4 digits)
into “[ ]”
–
z After scroll displays “Call 888-539-....” twice, displays “Call SIRIUS”.
Symptom Cause/Solution Page
Audyssey DSX™
cannot be selected.
Or “Not Available”
is displayed when
AUDYSSEY DSX
button is pressed.
• Check that “Speaker Config.” – “Front Height” or “Front Wide” is
set to other than “None”.
• Check that “Speaker Config.” – “Center” is set to other than
“None”.
• Switch the surround mode to STANDARD.
• Check that “Input Mode” is set to other than “EXT.IN”.
• When headphones are used, Audyssey DSX cannot be selected.
96
96
50
84
–
MultEQ
®
XT 32,
Dynamic EQ
®
and
Dynamic Volume
®
cannot be selected.
Or “Not Available”
is displayed when
MULTEQ button or
DYN EQ/VOL button
is pressed.
• Switch the surround mode to other than “DIRECT”or“PURE
DIRECT”.
• Check that “Input Mode” is set to other than “EXT.IN”.
• When headphones are used, MultEQ XT 32, Dynamic EQ and
Dynamic Volume cannot be selected.
52
84
–
Dynamic EQ and
Dynamic Volume
cannot be selected.
Or “Run Audyssey
Auto Setup” is
displayed when
DYN
EQ/VOL
button is
pressed.
• Make Audyssey Auto Setup. 7, 63
RESTORER cannot
be selected. Or
“Not Available” is
displayed when the
RESTORER button is
pressed.
• Check that an analog signal or PCM signal （fs=44.1/48kHz） is
input. For playback of multichannel signals such as Dolby Digital or
DTS surround, RESTORER cannot be used.
• Check that “Input Mode” is set to other than “EXT.IN”.
92
84
To Next Page
Loading...
Need help?
General
Weight and Dimensions
