To Next PageTo Next PageWhy is a specific part of a disc not playing on my Denon Receiver?
If a specific part of a disc isn't playing on your Denon Receiver, the disc may be dirty or scratched. Wipe the disc clean or replace it.
What to do if my Denon Receiver power turns off suddenly and the POWER indicator flashes red (2 second intervals)?
The protection circuit may have been activated because of a rise in internal temperature. Turn off the power, wait for the set to fully cool down, then turn the power back on. Also, ensure the set is in a well-ventilated location.
Why does my Denon Receiver power off suddenly and POWER indicator flashes red (0.25 second intervals)?
Turn off the power and contact a DENON service center.
What to do if my Denon Receiver display is lit but no sound is produced?
There are several reasons why your Denon Receiver might have a lit display but no sound: * The input source may be incorrect; select the appropriate input source. * The volume control may be set too low; turn the volume up. * MUTING may be activated; switch off MUTING.
Why can't my Denon Receiver play a CD-R or CD-RW disc?
If your Denon Receiver can't play a CD-R or CD-RW disc, it may not have been finalized. Finalize the disc, then try playing it. Alternatively, the recording conditions may be poor, or the disc quality might be lacking, so use a properly recorded disc.
What to do if my Denon Car Receiver display is off?
If the display on your Denon Car Receiver is off, check the Dimmer setting. If it's set to “OFF,” change it to something other than “OFF.”
What to do if my Denon Car Receiver display is not lit and no sound is produced when power is switched on?
If the display isn't lit and no sound is produced when you turn on your Denon Car Receiver, the power cord may not be plugged in securely. Check the connections on the set's rear panel and the connection of the power plug to the power outlet.
How to fix 'Server is not found' or connection issues on my Denon Receiver?
If your Denon Receiver displays 'Server is not found' or has connection issues, check the computer’s or router’s firewall settings. Ensure the computer is powered on and the server is running. Also, verify the set’s IP address.
Why does my Denon Receiver not operate properly?
The set may not operate properly because external noise or interference is causing the set to malfunction. Reset the microprocessor.
What to do if my Denon Receiver display is off?
If the display is off on your Denon Receiver, the Dimmer setting may be set to “OFF.” Set it to something other than “OFF.”
General| Frequency range | 5 - 20000 Hz |
|---|---|
| RMS rated power | 65 W |
| Pre-out channels | 1 SW |
| Input sensitivity | 200 mV |
| Pre-out connectivity | Yes |
| Audio output channels | 2.0 channels |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Total Harmonic Distortion (THD) | 0.7 % |
| Dynamic power per channel (4 Ohm) | 80 W |
| Power output per channel (20-20KHz@8 Ohm) | - W |
| Audio (L/R) in | 2 |
| Digital audio optical in | 1 |
| Headphone connectivity | 3.5 mm |
| Connectivity technology | Wired & Wireless |
| Speakers connectivity type | Binding post |
| Audio formats supported | AAC, FLAC, MP3, WMA |
| Image formats supported | JPG |
| Video formats supported | AVI, WMV |
| AM band range | 522 - 1611 kHz |
| FM band range | 87.5 - 108 MHz |
| Supported radio bands | AM, FM |
| Preset stations quantity | 99 |
| Internet radio services supported | Last.fm, Napster |
| Optical drive type | CD player |
| Disc types supported | CD, CD-R, CD-RW |
| Display | OLED |
| Product color | Silver |
| Audio decoders | Not supported |
| Volume control | Rotary |
| Apple docking compatibility | iPhone, iPod |
| Number of products included | 1 pc(s) |
| AC input voltage | 230 V |
| AC input frequency | 50 Hz |
| Power consumption (standby) | 0.4 W |
Weight and Dimensions| Depth | 299 mm |
|---|---|
| Width | 280 mm |
| Height | 112 mm |
| Weight | 4300 g |
