9
3.3 Programming Toggle Option
Sections
To program a section with toggle options from the
Escort5580 programming mode:
1. Enter the 3-digit section number.
2. The system announces the section you have
entered with the prompt:
“Section (number)”“Section (number)”
“Section (number)”“Section (number)”
“Section (number)”
The system announces which options are
presently turned ON with one of the following
prompts:
“All options are of“All options are of
“All options are of“All options are of
“All options are of
f”f”
f”f”
f”
“All options are on”“All options are on”
“All options are on”“All options are on”
“All options are on”
“Option (number) is on”“Option (number) is on”
“Option (number) is on”“Option (number) is on”
“Option (number) is on”
“Options (numbers) are on”“Options (numbers) are on”
“Options (numbers) are on”“Options (numbers) are on”
“Options (numbers) are on”
The system then prompts:
“Enter tw“Enter tw
“Enter tw“Enter tw
“Enter tw
o digit option. To digit option. T
o digit option. To digit option. T
o digit option. T
o Exit, presso Exit, press
o Exit, presso Exit, press
o Exit, press
pound”pound”
pound”pound”
pound”
3. To exit the section without making any changes,
press [#].
To turn an option ON or OFF, enter the 2-digit
option number.
If you enter an invalid option number, the
system prompts:
“Inv“Inv
“Inv“Inv
“Inv
alid entry”alid entry”
alid entry”alid entry”
alid entry”
After you enter a valid option number, the
system again announces which options are
ON.
4. When you have finished programming the
options in the section, press [#]. The system
returns to the “Enter a Section Number” prompt.
5. Record your new programming choices in the
appropriate section of the Programming
Worksheets.
3.4 Programming Label Entry
Sections
To program or change a label:
1. Enter the section number of the label. The
system announces the section number and
then recites the words presently programmed
in the label. Each label may have up to six
words. The system then prompts:
“Enter three digit w“Enter three digit w
“Enter three digit w“Enter three digit w
“Enter three digit w
ord. Tord. T
ord. Tord. T
ord. T
o exit, presso exit, press
o exit, presso exit, press
o exit, press
pound”.pound”.
pound”.pound”.
pound”.
2. Enter the first word of the label using the 3-digit
codes from the Label Library in Appendix B of
the Programming Worksheets.
The system beeps at the end of each correctly
entered code and the system prompts:
“Enter three digit w“Enter three digit w
“Enter three digit w“Enter three digit w
“Enter three digit w
ord. Tord. T
ord. Tord. T
ord. T
o exit presso exit press
o exit presso exit press
o exit press
pound”pound”
pound”pound”
pound”
If you make an invalid entry, the system
prompts:
“Inv“Inv
“Inv“Inv
“Inv
alid entryalid entry
alid entryalid entry
alid entry
. Enter three digit w. Enter three digit w
. Enter three digit w. Enter three digit w
. Enter three digit w
ord. Tord. T
ord. Tord. T
ord. T
oo
oo
o
exit press pound”exit press pound”
exit press pound”exit press pound”
exit press pound”
3. If you have more words to program, enter the
3-digit code of each word until you are finished.
4. When you have entered six words, the system
will recite the label. If your label is less than six
words, press [#].
5. To have the system read the new label to you,
enter the programming section for the label
again.
6. If the label is correct, press [#]. To change the
label again, repeat steps 1-5, above.
7. Record the new label in the appropriate section
of the Programming Worksheets.
Adding Numbers to Labels
Three special Number Commands are available to
allow the system to include a number in the voice
label. The number commands allow the system to
announce the number in three different modes:
Label 000: Number Command 1, Combined
Form. The number will be announced in its full
form. For example, the number 401 would be
announced as
“four hundred and one”
.
P R O G R A M M I N G
To Next Page
Loading...
Need help?
General
