46
Appendix E
The Access Code Programming function allows you to program access codes that will function on the
security system as well as on the Escort5580. The system can be set to accept 4 or 6 digit user codes.
Depending on what model of security system you have, you may have the ability to program either 6 or
37 access codes. To program these user codes, follow these steps:
With the system disarmed, access the security system using the steps described in the Accessing
Your Security System and Accessing Partitions section of this manual.
Press [
]. When the system announces:
“For Automation Control and User Programming, press [5].”“For Automation Control and User Programming, press [5].”
“For Automation Control and User Programming, press [5].”“For Automation Control and User Programming, press [5].”
“For Automation Control and User Programming, press [5].”
press [5]. The system will then announce:
“For Automation Control“For Automation Control
“For Automation Control“For Automation Control
“For Automation Control
,,
,,
,
press [1] press [1]
press [1] press [1]
press [1]
..
..
.
FF
FF
F
or User Programmingor User Programming
or User Programmingor User Programming
or User Programming
,,
,,
,
press [ press [
press [ press [
press [
33
33
3
]]
]]
]
..
..
.
TT
TT
T
o exito exit
o exito exit
o exit
,,
,,
,
press [#] press [#]
press [#] press [#]
press [#]
..
..
.
””
””
”
Press the [3] key. Enter your master access code. The system will then announce:
“User Code Programming. Enter the one-/tw“User Code Programming. Enter the one-/tw
“User Code Programming. Enter the one-/tw“User Code Programming. Enter the one-/tw
“User Code Programming. Enter the one-/tw
o- digit user number.o- digit user number.
o- digit user number.o- digit user number.
o- digit user number.
For User Option For User Option
For User Option For User Option
For User Option
Programming, press [9].Programming, press [9].
Programming, press [9].Programming, press [9].
Programming, press [9].
User X, Y and Z are programmed. TUser X, Y and Z are programmed. T
User X, Y and Z are programmed. TUser X, Y and Z are programmed. T
User X, Y and Z are programmed. T
o exit, press [#].”o exit, press [#].”
o exit, press [#].”o exit, press [#].”
o exit, press [#].”
Your system may or may not prompt you with “User Option Programming”. Please
consult your security system instruction manual for more information on user options.
Enter the number of the access code that you wish to program at this time. The system will announce:
“Enter the ne“Enter the ne
“Enter the ne“Enter the ne
“Enter the ne
w 4-/6- digit access code.w 4-/6- digit access code.
w 4-/6- digit access code.w 4-/6- digit access code.
w 4-/6- digit access code.
TT
TT
T
o exit, press [#].”o exit, press [#].”
o exit, press [#].”o exit, press [#].”
o exit, press [#].”
Enter the new code at this point. You will again be prompted by the message:
“User Code Programming. Enter the one-/tw“User Code Programming. Enter the one-/tw
“User Code Programming. Enter the one-/tw“User Code Programming. Enter the one-/tw
“User Code Programming. Enter the one-/tw
o- digit user number.o- digit user number.
o- digit user number.o- digit user number.
o- digit user number.
For User Option Programming, press [9].For User Option Programming, press [9].
For User Option Programming, press [9].For User Option Programming, press [9].
For User Option Programming, press [9].
Users X, Y and Z are programmed. TUsers X, Y and Z are programmed. T
Users X, Y and Z are programmed. TUsers X, Y and Z are programmed. T
Users X, Y and Z are programmed. T
o exit, press [#].”o exit, press [#].”
o exit, press [#].”o exit, press [#].”
o exit, press [#].”
If you wish to program another access code, enter the user number. If not, press [#] to return to the
main menu.
A C C E S S C O D E P R O G R A M M I N G
To Next Page
Loading...
Need help?
General
