8
The following sections describe how to program
the Escort5580. All Escort5580 programming can
be done via any local touchtone telephone or via
the DLS software.
It is extremely important that you read
this section of the manual completely
before attempting to program the
Escort5580 module.
3.1 Entering Installer
Programming
With the system disarmed:
1. Pick up a local telephone handset. You will
hear:
Dial TDial T
Dial TDial T
Dial T
one.one.
one.one.
one.
2. Enter the Telephone Access code. The default
Telephone Access code is [***]. (You can
reprogram this code in section [020].) The
system prompts:
“Hello”“Hello”
“Hello”“Hello”
“Hello”
3. Enter programming mode by pressing [✱][8].
The system prompts:
“Enter the Service Code”“Enter the Service Code”
“Enter the Service Code”“Enter the Service Code”
“Enter the Service Code”
4. Enter the 4-digit Service code. The default service
code is [5580]. (You can change the service
code in programming section [001].) After the
service code is entered, the system prompts:
“Enter a Section Number. T“Enter a Section Number. T
“Enter a Section Number. T“Enter a Section Number. T
“Enter a Section Number. T
o exit, presso exit, press
o exit, presso exit, press
o exit, press
[#]”[#]”
[#]”[#]”
[#]”
5. To enter a programming section, enter the 3-digit
number of the section. If you make an error
entering the section number, the system prompts:
“Inv“Inv
“Inv“Inv
“Inv
alid entryalid entry
alid entryalid entry
alid entry
. Enter a Section Number.. Enter a Section Number.
. Enter a Section Number.. Enter a Section Number.
. Enter a Section Number.
TT
TT
T
o exit, press [#]”o exit, press [#]”
o exit, press [#]”o exit, press [#]”
o exit, press [#]”
When you enter a section number, the system
announces the section you have entered with
the prompt:
“Section (number)”“Section (number)”
“Section (number)”“Section (number)”
“Section (number)”
3.2 Programming Data Entry
Sections
To program a data entry section from the Escort5580
programming mode:
1. Enter the 3-digit section number.
2. The system announces the section you have
entered with the prompt:
“Section (number)”“Section (number)”
“Section (number)”“Section (number)”
“Section (number)”
The system announces the data presently
programmed in the programming section as:
“Data is (data)”“Data is (data)”
“Data is (data)”“Data is (data)”
“Data is (data)”
The system then prompts:
“Enter ne“Enter ne
“Enter ne“Enter ne
“Enter ne
w data”w data”
w data”w data”
w data”
3. Enter the new data in the section, or return to
the “Enter a Section Number” prompt, by
pressing [#].
When you have finished entering the new data,
the system announces the new data with the
prompt:
“Data is (data)”“Data is (data)”
“Data is (data)”“Data is (data)”
“Data is (data)”
If you make an invalid data entry, the system
announces:
“Inv“Inv
“Inv“Inv
“Inv
alid Entryalid Entry
alid Entryalid Entry
alid Entry
. Data is (data). Enter. Data is (data). Enter
. Data is (data). Enter. Data is (data). Enter
. Data is (data). Enter
nene
nene
ne
w data. Tw data. T
w data. Tw data. T
w data. T
o exit, press pound.”o exit, press pound.”
o exit, press pound.”o exit, press pound.”
o exit, press pound.”
4. Record the new data in the appropriate section
of the Programming Worksheets.
S E C T I O N 3
How to Program
To Next Page
Loading...
Need help?
General
