Eighteeth E-connect S

Questions and Answers

P
pittspatriciaAug 28, 2025
Why motor spontaneously starts running in reverse in Eighteeth E-connect S Dental equipment?
- D
  Denise McbrideAug 28, 2025
  If the motor in your Eighteeth dental equipment spontaneously starts running in reverse, consider these possibilities: * The torque limit might be set too high. Check if the torque limit is sufficient. * The apical action setting might be set to reverse. Change the setting if it’s not expected. * The device might be set to REV mode. Change the setting if it’s not expected.
V
victorcookAug 27, 2025
Why the motor doesn't rotate in Eighteeth E-connect S Dental equipment?
- C
  Cheryl SantosAug 27, 2025
  If the motor in your Eighteeth dental equipment isn’t rotating, it could be due to these reasons: * The mode might be set to M0, which is a stand-alone apex locator function. Change to M1-M10. * The contra-angle might be clogged. Clean or replace it.
J
James RoblesAug 27, 2025
What to do if there is no charge indicator flash on handpiece screen of Eighteeth E-connect S?
- S
  Stephanie FullerAug 27, 2025
  If there is no charge indicator flashing on the handpiece screen of your Eighteeth dental equipment, consider the following: * The handpiece might be placed in the charge base in the wrong direction. Check the direction. * The charge pin of the charge base might be unable to rebound. Remove any debris between the moving part and the base of the charge pin. * The contactors might be dirty. Clean the surface of the contactors. * The charge base might be broken. Try connecting the adapter directly to the handpiece.
B
Brandon StuartAug 25, 2025
What to do if the motor can’t stop in Eighteeth E-connect S?
- M
  Michele YoungAug 26, 2025
  If the motor in your Eighteeth dental equipment won’t stop, here’s what you can do: * The auto-stop function might be off. Press the main switch to stop it, and turn the auto-stop function on if necessary. * There could be a short circuit inside the motor handpiece or the motor handpiece cord. Press the “S” button to stop the motor.
M
mosspeterAug 25, 2025
Why the power LED on charge base does not light in Eighteeth E-connect S?
- M
  Mrs. Amy RangelAug 25, 2025
  If the power LED on the charge base of your Eighteeth dental equipment isn't lighting up, here are some things to investigate: * You might be using the wrong adapter. Use the original adapter. * The adapter might not be properly connected. Check the connection. * The plug of the adapter might not be fully inserted into the outlet. Ensure it's properly connected. * There might not be electricity in the outlet. Check the connection.

Summary

3. Before Use

3.2 Contraindications

4. Installing the E-connect S

4.1 Installation of the Contra Angle

Instructions for securely attaching the contra-angle to the handpiece, including rotation options.

4.2 Install the File

4.3 Connecting Measuring Wire

4.4 Connecting Charge Base

5. Use Interface

5.1 Panel Key

5.2 Screen Display

6. Setting

6.1 Selecting Memory

6.2 Setting Parameters

Instructions for adjusting speed, torque, and other operational parameters for specific treatments.

7. Operation

7.2 Motor Operation

Details on operating the motor for dental procedures, including speed and torque indications.

7.3 Apex Operation and Not Suitable Condition

Covers apex locator usage and identifies root canal conditions that may affect measurement accuracy.

8. Maintenance

Autoclavable Components

Lists the specific parts of the E-connect S that can be safely autoclaved for sterilization.

Autoclavable Procedure

Step-by-step instructions for cleaning, disinfecting, lubricating, and sterilizing components.

Disinfection Components

9. Error Warning

Overload and Overheat Warnings

Explains overload and overheat conditions and the necessary actions to take.

Hardware and Motor Faults

Describes fault conditions related to the handpiece hardware or motor, requiring distributor contact.

Low Power Warning

10. Troubleshooting

Power and Charging Issues

Addresses problems related to the device not turning on or the charge LED not lighting up.

Motor and Apex Function Issues

Resolves issues like the motor not rotating, not stopping, or not reversing correctly.

Measurement and Sound Issues

Covers problems with unstable measurements, no sound, or alarms during operation.

Eighteeth E-connect S Specifications

General

Category	Dental equipment
Adaptive Torque Reverse	Yes
Apex Locator Integration	Yes
Display	OLED
Battery	Rechargeable Lithium-ion
Weight	150 g
Type	Endodontic motor
Torque Range	0.4 Ncm - 5.0 Ncm
Speed Range	100 rpm - 1200 rpm
Battery Capacity	2000 mAh