Elmo MX-P User Manual

5
BEFORE YOU USE
■ Be sure to use the cable supplied with the product.
■ The supplied power cord and AC adapter are designed for exclusive use with this product. Do
not use them with other products.
■ Be sure to use the power cord applicable to your local power specifications. If the product was
sold in Japan, use the AC adapter sold with the product with 100 VAC and 50 or 60 Hz.
■ When storing the product, do not leave it under direct sunlight or by heaters. It may be
discolored, deformed, or damaged.
■ Do not place this product in any humid, dusty, salt bearing wind, or vibrating locations.
Use it under the following environmental conditions:
Temperature：0℃～ 40℃ Humidity：30％～ 85％(No condensation)
■ Use a soft, dry cloth for cleaning. Do not use any volatile solvent such as thinner or benzene.
■ Luminescent and Black Spots
There may be some pixels that do not properly operate due to the use of CMOS Area Image
Sensors made-up of many pixels.
Though luminescent or black spots may be found on the screen, it is a phenomenon peculiar to
the CMOS Area Image Sensors and is not a malfunction.
■ Follow the guidelines below to prevent the unit from dropping or overturning.
・ Use the product on a stable base, desk, or table. Do not place the product on an unstable
base or slanted location.
・ Place or wire the product so as to prevent the cables from being pulled or drawn.
■ Do not point the lens directly to the sun. It could degrade the imaging capability.
■ Do not look directly into the LED light. If you look directly into it at pointblank range, your eyes
may be injured.
■ If this product is used for longer than the warranty period, its performance and quality may
deteriorate due to the lifetime of its parts. For parts replacement (on chargeable basis), consult
the dealer from whom you purchased this product or our branch/office near your location.
■ Copyright
Unless used for personal use, it is prohibited strictly under copyright law to use any photo files
without the prior consent of the copyright holder. Even if using for personal use, be careful that
there could be a situation where video or audio recording is restricted or illegal.
■ The contents of this document are subject to change without notice. The latest version is
available from the following official website:
https://www.elmousa.com https://www.elmoeurope.com
■ It is prohibited under copyright law to use or copy any part or the whole of this document
without our prior written consent.
■ ELMO shall not be liable for any claim for damage or loss of earnings or any claim raised by a
third person due to the use, malfunction or repair of this product.
HANDLING PRECAUTIONS
The followings are special precautions against mishandling of the product. Pay close attention
to them.
②Setting up
When setting up the MX-P,
hold the body around the
operating panel.
Be careful not to pinch
your fingers.
①Installation
Do not place the MX-P
on an unstable place or
slanted surface
③Carrying the MX-P
Carry the MX-P by folding the arm so as not to damage
the camera.
Do not carry by holding the arm or camera head.

Elmo MX-P Specifications

General

Auto focus	Yes
Digital zoom	16 x
Shooting area (WxD)	373.3 x 281.9 mm
Lamp type	LED
Product color	White
Sensor type	-
Maximum frame rate	60 fps
Optical sensor size	- \
Supported graphics resolutions	1920 x 1080 (HD 1080), 3840 x 2160
Interface	USB 3.2 Gen 1 (3.1 Gen 1)
USB connector type	Micro-USB B
VGA (D-Sub) output ports	1
Operating voltage	5 V
Power supply type	DC
Power consumption (typical)	4.6 W

Weight and Dimensions

Depth	81.2 mm
Width	324.9 mm
Height	302 mm
Weight	544 g
Dimensions folded (WxDxH)	289.5 x 81.2 x 22.8 mm