ELTEX MES53xx User Manual

MES53xx, MES33xx, MES23xx Ethernet Switch Series 117
console(config)#
Table 5.111. Global configuration mode commands
Command
Value/Default value
Action
ip multicast-routing pim
-/Disabled by default
Enable multicast routing and PIM protocol on all interfaces.
no ip multicast-routing pim
Disable multicast routing and PIM.
ipv6 multicast-routing pim
-/Disabled by default
Enable multicast routing and PIM for IPv6 on all interfaces.
no ipv6 multicast-routing
pim
Disable multicast routing and PIM for IPv6.
ip pim accept-register list
acc_list
acc_list: (0..32) characters.
Filter PIM registration messages.
- acc_list - a standard ACL list of multicast prefixes.
no ip pim accept-register
list
Disable this parameter.
ipv6 pim accept-register
list acc_list
acc_list: (0..32) characters.
Filter PIM registration messages for IPv6.
- acc_list - a standard ACL list of multicast prefixes.
no ipv6 pim accept-register
list
Disable this parameter.
ip pim bsr-candidate
ip_address [mask] [priority
priority_num]
mask: (8..32)/30;
priority_num: (0..192)/0.
Specify the device as a BSR (bootstrap router) candidate.
- ip_address - a valid IP address of the switch;
- mask - subnet mask;
- priority_num - priority.
no ip pim bsr-candidate
Disable this parameter.
ipv6 pim bsr-candidate
ipv6_address [mask]
[priority priority_num]
mask: (8..128)/126;
priority_num: (0..192)/0.
Specify the device as a BSR (bootstrap router) candidate.
- ipv6_address - a valid IPv6 address of the switch;
- mask - subnet mask;
- priority_num - priority.
no ipv6 pim bsr-candidate
Disable this parameter.
ip pim rp-address
unicast_address
[multicast_subnet]
-
Create a static rendezvous Point (RP); optionally specify a
multicast subnetwork for this RP.
- unicast_addr - IP address;
- multicast - multicast subnetwork.
no ip pim rp-address
unicast_address
[multicast_subnet]
Delete a static RP or RP for a specific subnetwork.
ipv6 pim rp-
addressipv6_unicast_addre
ss [ipv6_multicast_ subnet]
-
Create a static rendezvous Point (RP); optionally specify a
multicast subnetwork for this RP.
- ipv6_unicast_ addr IPv6 address;
- ipv6_multicast_ subnet - multicast subnetwork.
no ipv6 pim rp-
addressipv6_unicast_addre
ss [ipv6_multicast_subnet]
Delete a static RP or RP for a specific subnetwork.
ip pim rp-candidate
unicast_address [group-list
acc_list] [priority priority]
[interval secs]
acc_list: (0..32) characters;
priority: (0..192)/192;
secs: (1..16383)/60
seconds.
Create a Rendezvous Point (RP) candidate.
- unicast_addr - IP address;
- acc_list - a standard ACL list of multicast prefixes;
-priority - candidate priority;
- secs - message sending period.
no ip pim rp-candidate
unicast_address
Disable this parameter.
ipv6 pim rp-candidate
ipv6_unicast_address
[group-list acc_list]
[priority priority] [interval
secs]
acc_list: (0..32) characters;
priority: (0..192)/192;
secs: (1..16383)/60
seconds.
Create a Rendezvous Point (RP) candidate.
- ipv6_unicast_addr - Ipv6 address;
- acc_list - a standard ACL list of multicast prefixes;
- priority - candidate priority;
- secs-message sending period.
no ipv6 pim rp-candidate
ipv6_unicast_address
Disable this parameter.
ip pim ssm {range
multicast_subnet | default}
-
Specify a multicast subnetwork
- range - specify a multicast subnetwork;
- multicast_subnet - multicast subnetwork;
- default - specify a range in 232.0.0.0/8.
no ip pim ssm [range
multicast_subnet | default]
Disable this parameter.

ELTEX MES53xx Specifications

General

Brand	ELTEX
Model	MES53xx
Category	Switch
Language	English