Endress+Hauser Liquiphant FTL64 - Table of Contents

Liquiphant FTL64 HART Table of contents
Endress+Hauser 3
Table of contents
1 About this document ................ 6
1.1 Purpose of this document ................. 6
1.2 Symbols ............................. 6
1.2.1 Safety symbols .................. 6
1.2.2 Electrical symbols ................ 6
1.2.3 Tool symbols .................... 6
1.2.4 Communication-specific symbols ..... 6
1.2.5 Symbols for certain types of
information .................... 6
1.2.6 Symbols in graphics ............... 7
1.2.7 Registered trademarks ............. 7
2 Basic safety instructions ............ 7
2.1 Requirements for the personnel ............ 7
2.2 Intended use .......................... 7
2.2.1 Incorrect use .................... 8
2.3 Workplace safety ....................... 8
2.4 Operational safety ...................... 8
2.5 Product safety ......................... 8
2.6 Functional Safety SIL (optional) ............ 9
2.7 IT security ............................ 9
2.8 Device-specific IT security ................ 9
3 Product description ................. 9
3.1 Product design ....................... 10
4 Incoming acceptance and product
identification ..................... 10
4.1 Incoming acceptance ................... 10
4.2 Product identification ................... 11
4.2.1 Nameplate .................... 11
4.2.2 Manufacturer address ............ 11
4.3 Storage and transport .................. 11
4.3.1 Storage conditions ............... 11
4.3.2 Transporting the device ........... 11
5 Mounting ......................... 12
5.1 Mounting requirements ................. 12
5.1.1 Pay attention to the temperature for
devices with a PFA coating
(conductive) ................... 13
5.1.2 Take switch point into consideration . 13
5.1.3 Take viscosity into consideration .... 13
5.1.4 Avoid buildup .................. 14
5.1.5 Take clearance into consideration ... 15
5.1.6 Support the device .............. 15
5.2 Mounting the device ................... 16
5.2.1 Required tool .................. 16
5.2.2 Installation .................... 16
5.3 Sliding sleeves ....................... 19
5.4 Post-mounting check ................... 19
6 Electrical connection .............. 20
6.1 Required tool ......................... 20
6.2 Connecting requirements ............... 20
6.2.1 Cover with securing screw ......... 20
6.2.2 Potential equalization ............ 20
6.3 Connecting the device .................. 21
6.3.1 Supply voltage ................. 21
6.3.2 Terminals ..................... 21
6.3.3 Cable specification ............... 21
6.3.4 4-20 mA HART ................. 22
6.3.5 Overvoltage protection ........... 22
6.3.6 Wiring ....................... 23
6.3.7 Terminal assignment ............ 23
6.3.8 Cable entries ................... 24
6.3.9 Available device plugs ............ 24
6.4 Ensuring the degree of protection ......... 25
6.4.1 Degree of protection ............. 25
6.5 Post-connection check .................. 25
7 Operation options ................. 26
7.1 Overview of operating options ............ 26
7.2 4 to 20 mA HART (FEL60H) electronic
insert .............................. 26
7.3 Function test using operating key on
electronic insert ....................... 27
7.4 Structure and function of the operating
menu .............................. 28
7.4.1 User roles and related access
authorization .................. 28
7.5 Access to the operating menu via the local
display ............................. 28
7.5.1 Device display (optional) .......... 28
7.5.2 Operation via Bluetooth® wireless
technology (optional) ............ 29
7.6 Access to the operating menu via the
operating tool ........................ 30
7.7 HistoROM data management ............. 30
8 System integration ................ 30
8.1 Overview of device description files ......... 30
8.2 Measured variables via HART protocol ...... 30
8.2.1 Device variables and measured
values ........................ 31
8.2.2 System units ................... 31
9 Commissioning ................... 31
9.1 Preliminaries ........................ 31
9.1.1 As-delivered state ............... 32
9.2 Function check ....................... 32
9.3 Switching on the device ................. 32
9.4 Establishing a connection via FieldCare and
DeviceCare .......................... 32
9.4.1 Via HART protocol ............... 32