Endress+Hauser Proline Promass I 100 - Page 4

Table of contents Proline Promass I 100 Modbus RS485
4 Endress+Hauser
10.4 Advanced settings ..................... 51
10.4.1 Defining the tag name ............ 51
10.4.2 Calculated values ................ 51
10.4.3 Carrying out a sensor adjustment .... 52
10.4.4 Configuring the totalizer .......... 53
10.5 Simulation ........................... 54
10.5.1 Parameter overview with brief
description .................... 55
10.6 Protecting settings from unauthorized
access .............................. 55
10.6.1 Write protection via write protection
switch ........................ 55
11 Operation ......................... 57
11.1 Read device locking status ............... 57
11.2 Reading measured values ................ 57
11.2.1 Process variables ................ 57
11.2.2 Totalizer ...................... 58
11.3 Adapting the measuring device to the process
conditions ........................... 59
11.4 Performing a totalizer reset .............. 59
12 Diagnostics and troubleshooting ... 61
12.1 General troubleshooting ................. 61
12.2 Diagnostic information via light emitting
diodes .............................. 61
12.2.1 Transmitter .................... 61
12.2.2 Safety Barrier Promass 100 ........ 62
12.3 Diagnostic information in FieldCare ........ 62
12.3.1 Diagnostic options ............... 62
12.3.2 Calling up remedy information ...... 63
12.4 Diagnostic information via communication
interface ............................ 63
12.4.1 Reading out diagnostic information .. 63
12.4.2 Configuring error response mode .... 64
12.5 Adapting the diagnostic information ....... 64
12.5.1 Adapting the diagnostic behavior .... 64
12.6 Overview of diagnostic information ........ 65
12.7 Pending diagnostic events ............... 67
12.8 Diagnostic list ........................ 67
12.9 Event logbook ........................ 68
12.9.1 Event history ................... 68
12.9.2 Filtering the event logbook ........ 68
12.9.3 Overview of information events ..... 68
12.10 Resetting the measuring device ........... 69
12.11 Device information .................... 69
12.12 Firmware history ...................... 70
13 Maintenance ...................... 71
13.1 Maintenance tasks ..................... 71
13.1.1 Exterior cleaning ................ 71
13.1.2 Interior cleaning ................ 71
13.2 Measuring and test equipment ............ 71
13.3 Endress+Hauser services ................ 71
14 Repair ............................ 72
14.1 General notes ........................ 72
14.2 Spare parts .......................... 72
14.3 Endress+Hauser services ................ 72
14.4 Return .............................. 72
14.5 Disposal ............................ 72
14.5.1 Removing the measuring device ..... 72
14.5.2 Disposing of the measuring device ... 73
15 Accessories ....................... 74
15.1 Device-specific accessories ............... 74
15.1.1 For the sensor .................. 74
15.2 Communication-specific accessories ........ 74
15.3 Service-specific accessories ............... 75
15.4 System components .................... 75
16 Technical data .................... 76
16.1 Application .......................... 76
16.2 Function and system design .............. 76
16.3 Input ............................... 76
16.4 Output ............................. 78
16.5 Power supply ......................... 80
16.6 Performance characteristics .............. 81
16.7 Installation .......................... 85
16.8 Environment ......................... 85
16.9 Process ............................. 86
16.10 Mechanical construction ................ 88
16.11 Operability .......................... 90
16.12 Certificates and approvals ............... 90
16.13 Application packages ................... 92
16.14 Accessories .......................... 93
16.15 Documentation ....................... 93
17 Appendix ......................... 94
17.1 Overview of the operating menu ........... 94
Index ................................. 110