To Next PageTo Next Page
Need help?Do you have a question about the Endress+Hauser Proline Promass P 300 and is the answer not in the manual?
General| Device Type | Coriolis flowmeter |
|---|---|
| Measurement Principle | Coriolis |
| Process Pressure | up to 40 bar |
| Output Signals | 4-20 mA, HART, PROFIBUS |
| Housing Material | Aluminum, stainless steel |
| Sensor Material | Stainless steel |
| Protection Class | IP67 |
| Ambient Temperature Range | -40 to +60 °C |
| Approval | ATEX, IECEx |
Product name and designation for the Coriolis flowmeter.
Specifies the product type as a Coriolis flowmeter.
Explanation of symbols used throughout the manual.
Details the Coriolis force-based measurement principle.
Description of the transmitter component and its materials.
Description of the sensor component and its materials.
Measures and functions for device cybersecurity.
Identifies the primary measured variables of the device.
Specifies the available measuring ranges for liquids.
Details the types of input signals supported by the device.
Overview of selectable output and input configurations.
Detailed specifications for different output signal types.
Specifies safety parameters for Ex-rated devices.
Defines intrinsically safe parameters for specific Ex connections.
Details terminal assignments for power and signal connections.
Lists available device plugs for fieldbus and service interfaces.
Provides detailed pin assignments for device plugs.
Specifies voltage ranges for different power supply options.
Details the device's power consumption and current draw.
Describes device behavior during power supply interruptions.
General guidance on electrical connection procedures.
Specifications for spring-loaded terminals.
Details available cable entry types and threads.
General requirements for cable selection and temperature range.
Specifics on cable types, impedance, and shielding.
Defines standard conditions for performance specifications.
Specifies the limits for measurement error.
Details the fundamental accuracy specifications.
Provides data on the stability of the zero point reading.
Presents flow rate data based on nominal diameter.
Explains the basis for accuracy and repeatability calculations.
Guidance on avoiding errors and installing in down pipes.
Recommendations for sensor orientation and securing methods.
Details when and how to perform zero point adjustments.
Specifies operating and display temperature limits.
Defines the permissible storage temperature range.
Indicates the climate class rating of the device.
Details the IP ratings for the device and its modules.
Specifies temperature ranges for standard and extended versions.
Provides density range information for the device.
Diagrams showing permissible pressure vs. temperature limits.
Guidance on selecting flow limits based on pressure loss.
Ensures adequate system pressure to prevent cavitation.
Options and recommendations for thermal insulation.
Describes available heating options for the sensor.
Information on the device's resistance to plant vibrations.
Material and properties of the sensor housing.
Material specification for the measuring tubes.
Materials used for various process connection types.
Details on seals for process connections.
Description of available accessories for the sensor.
Physical dimensions in millimeters for compact version.
Physical dimensions in inches for compact version.
Specifications for EN 1092-1 flanges.
Specifications for ASME B16.5 flanges.
Specifications for JIS B2220 flanges.
Specifications for DIN 11864-2 fixed flanges.
Specifications for BBS fixed flanges.
Specifications for BBS small sterile orbital flanges.
Details on Tri-Clamp connections.
Specifications for Tri-Clamp connections to DIN 11866 Series C.
Specifications for eccentric Tri-Clamp connections.
Specifications for DIN 32676 clamp connections.
Specifications for ISO 2852 clamp connections.
Specifications for DIN 11864-3 clamp connections.
Specifications for BBS clamp connections.
Specifications for BBS Quick Connect clamp connections.
Specifications for Neumo BioConnect clamp connections.
Specifications for DIN 32676 eccentric clamp connections.
Specifications for ISO 2852 eccentric clamp connections.
Specifications for BBS eccentric clamp connections.
Specifications for Neumo BioConnect eccentric clamp connections.
Specifications for DIN 11851 threaded connections.
Specifications for DIN 11864-1 threaded connections.
Specifications for SMS 1145 threaded hygienic connections.
Specifications for BBS threaded connections.
Specifications for BBS sterile orbital threaded connections.
Specifications for ISO 2853 threaded hygienic connections.
Accessory to protect the device from environmental effects.
Accessory for external display and operation.
Optional accessory for wireless network connectivity.
Details the materials used for the transmitter housing.
Material specification for the display window.
Material specification for seals.
Details cable entry types and materials.
Material specification for the device plug.
Materials used for sensor housing, tubes, connections, and seals.
User interface structure for tasks like commissioning and operation.
Lists the languages supported for device operation.
Methods for operating the device locally.
Description of display elements and operating controls.
Remote operation options using HART communication.
Remote operation options using FOUNDATION Fieldbus.
Remote operation options using PROFIBUS DP.
Remote operation options using PROFIBUS PA.
Remote operation options using Modbus RS485.
Remote operation options using EtherNet/IP.
Network topology for EtherNet/IP and PROFINET.
Network topology for EtherNet/IP and PROFINET.
Connection method using a wired service interface.
Connection method using the wireless WLAN interface.
Details WLAN function, encryption, and antenna options.
Describes automatic and manual data backup procedures.
Covers CE Mark, C-Tick Symbol, and Ex Approval.
Details various Ex protection types and North American approvals.
Covers sanitary, pharma compatibility, and functional safety.
Certifications for HART, Fieldbus, Profibus, EtherNet/IP, PROFINET.
Covers PED, Radio, CRN, tests, and other industry standards.
Enhancements for device functionality, safety, or specific needs.
Details on specific diagnostic function packages like Extended HistoROM.
Application package for traceable verification and monitoring.
Application package for calculating and outputting fluid concentrations.
Application package for high-precision density measurement.
Application package for IoT and SCADA integration.
Accessories directly related to the transmitter unit.
Accessories specifically for the sensor component.
Accessories enabling HART and Fieldbus communication.
Accessories for device service, configuration, and management.
Related system components like data managers and transmitters.
Core manuals like brief operating instructions.
Concise guides for initial setup and operation.
Detailed explanation of all device parameters.
Safety instructions for hazardous areas.
Documentation specific to the DKX001 accessory.
Specific guides for application packages.
Manuals detailing installation procedures for accessories.
List of registered trademarks relevant to the product.
