Extron electronics IN1804 Series - Page 76

IN1804 Seamless Scaling Switchers • SIS Configuration and Control 68
Command ASCII Command
(Host to Switcher)
Response
(Switcher to Host)
Additional Description
Logos (continued)
Clear Logo
Clear logo slot
E
X3*
X4#
PRST
}
PrstX3*
X4#]
Clear logo slot
X4#
and change its name
to [unassigned].
Logo Name
Write name
E
L
X4#
,
X1$
UNAM
}
Unam L
X4#
,
X1$]
Assign logo name
X1$
to logo
X4#
.
View logo name
E
L
X4#
UNAM
} X1$ ]
View the name assigned to logo
X4#
.
Logo Availability
View logo availability
E
Q LOGO
}
<16 characters>*<1 character>*<1 character>
]
Verbose modes 2 and 3:
Logo Q <16 characters>*<1 character>*<1 character>
]
1 = saved, 0 = empty
NOTE: The first 16 digits denote logo images, the digit immediately following the first * indicates the screen saver logo,
and the last digit (following the second *) indicates the HDCP logo.
Logo On or Off
Disable logo
E
E1*0LOGO
}
LogoE1*0
]
Disable display of the current full screen
notification logo.
Enable logo
E
E1*
X4#
LOGO
}
LogoE1*
X4#]
Display the logo assigned to slot
X4#
.
View logo status
E
E 1LOGO
}
X4#]
View logo slot
X4#
for which the logo is
enabled.
Horizontal Shift (Logo)
Specific value
E
L
X4#
*
X1^
HCTR
}
HctrL
X4#
*
X1^]
Set the horizontal centering of logo
X4#
to
X1^
.
Increment value
E
L
X4#
+HCTR
}
HctrL
X4#
*
X1^]
Shift logo right 1 pixel.
Decrement value
E
L
X4#
– HCTR
}
HctrL
X4#
*
X1^]
Shift logo left 1 pixel.
View
E
L
X4#
HCTR
}
X1^]
View horizontal centering value
X1^
.
Vertical Shift (Logo)
Specific value
E
L
X4#
*
X1^
VCTR
}
VctrL
X4#
*
X1^]
Set the vertical centering of logo
X4#
to
X1^
.
Increment value
E
L
X4#
+VCTR
}
VctrL
X4#
*
X1^]
Shift logo down 1 pixel.
Decrement value
E
L
X4#
– VCTR
}
VctrL
X4#
*
X1^]
Shift logo up 1 pixel.
View
E
L
X4#
VCTR
}
X1^]
View vertical centering value
X1^
.
KEY:
X1$
= Logo name (text label)
Up to 32 characters, excluding , (comma) ,*, and
|
.
X1^
= Horizontal or vertical position (shift)
The position is ± the horizontal or vertical position of the highest output
resolution.
• Response is five digits, padded with zeros and preceded by + or –.
• The logo vertical position allows up to ± 2400.
X4#
= User logo number
1 through 16. The response is three digits padded with leading zeros.
101 = No signal, screen saver user logo or image is displayed.
201 = User HDCP logo displayed