FLIR
Commercial S
y
stems,
2016.
All
rights
rese
r
v
ed
worldwide.
No
parts
of this man ual
, in
whole or in
part,
may
be copied
, photocopied, translated, or
transmitted
to any
electro
n
ic
medium
or machine
readable
form w i t h o u t
the
p r i o r w r i t t e n
permission
of FLIR
Commercia
l
Sy
stems
Names
and m a r k s
appearing
on the p r o d u c t s
herein are either registered trademarks or
trademarks
of
FLIR
Commercial Systems
and/or
its subsidiaries
.
All
other trademarks, trade names,
or company
names
referenced herein are used
for
identification
only and a r e
the
property
of
their respective owners.
This
product
i
s
protected
by
patents, design patents, patents pending,
or design
p
atents
pendi
ng.
If
you have q u e s t i o n s
that are
not covered
in this manual
,
or need
ser
v
ice,
contact
FLIR
Commercial Systems
Customer Support
at 805.964.9797
for
additional information
prior to
returning a came
ra.
This documentation and the requirements specified herein are subject to change without notice.
This
equipment must
be disposed
of
as electronic
waste.
Contact
your
nearest
FLIR
Commerci
a
l
Systems,
Inc.
representative
for
instructions
on how to
return
the p r o d u c t
to FLIR for
proper
di
sposal
.
FCC Notice. This device is a subassembly designed for incorporation into other products in order to provide an infrared camera
function. It is not an end-product fit for consumer use. When incorporated into a host device, the end-product will generate, use,
and radiate radio frequency energy that may cause radio interference. As such, the end-product incorporating this subassembly
must be tested and approved under the rules of the Federal Communications Commission (FCC) before the end-product may be
offered for sale or lease, advertised, imported, sold, or leased in the United States. The FCC regulations are designed to provide
reasonable protection against interference to radio communications. See 47 C.F.R. §§ 2.803 and 15.1 et seq.
Industry Canada Notice. This device is a subassembly designed for incorporation into other products in order to provide an
infrared camera function. It is not an end-product fit for consumer use. When incorporated into a host device, the end-product will
generate, use, and radiate radio frequency energy that may cause radio interference. As such, the end-product incorporating this
subassembly must be tested for compliance with the Interference-Causing Equipment Standard, Digital Apparatus, ICES-003, of
Industry Canada before the product incorporating this device may be: manufactured or offered for sale or lease, imported,
distributed, sold, or leased in Canada.
Avis d’Industrie Canada. Cet appareil est un sous-ensemble conçu pour être intégré à un autre produit afin de fournir une
fonction de caméra infrarouge. Ce n’est pas un produit final destiné aux consommateurs. Une fois intégré à un dispositif hôte, le
produit final va générer, utiliser et émettre de l’énergie radiofréquence qui pourrait provoquer de l’interférence radio. En tant que
tel, le produit final intégrant ce sous-ensemble doit être testé pour en vérifier la conformité avec la Norme sur le matériel
brouilleur pour les appareils numériques (NMB-003) d’Industrie Canada avant que le produit intégrant ce dispositif puisse être
fabriqué, mis en vente ou en location, importé, distribué, vendu ou loué au Canada.
EU Notice. This device is a subassembly or component intended only for product evaluation, development or incorporation into
other products in order to provide an infrared camera function. It is not a finished end-product fit for general consumer use.
Persons handling this device must have appropriate electronics training and observe good engineering practice standards. As such,
this product does not fall within the scope of the European Union (EU) directives regarding electromagnetic compatibility (EMC).
Any end-product intended for general consumer use that incorporates this device must be tested in accordance and comply with all
applicable EU EMC and other relevant directives.
To Previous Page
