Friedrich DSSXEMWRT3 - Warranty Information

100 pages

To Next Page

To Previous Page

Warranty Information

For the most recent warranty information, please visit

www.friedrich.com.

Main Page

Default Chapter2
- Table of Contents2
How to Use this Manual6
Introduction7
- Skus Referenced in this Manual8
- Equipment Nomenclature9
- Installation Considerations10
General: Network Installation11
- Notice11
- Connecting the Antenna Module12
- Connecting the Ethernet Cable13
- Powering on the Server14
- Configuring the Online Connection Kit15
General: HVAC Controller Installation16
- Introduction16
- Installing the HVAC Controller in 24VAC Relay Units17
- Using the HVAC Controller to Power a Wireless Thermostat (Optional)18
- Using the HVAC Controller's Dry Contacts to Control External Devices19
General: Thermostat Installation20
- Mounting the Thermostat to the Wall20
General: Sensor Installation21
- Mounting a Remote Wireless Sensor (Optional)21
General: Thermostat Configuraton22
- Understanding the Thermostat Screen22
- Configuring the Thermostat23
- Pairing the Thermostat and the HVAC Controller24
- Setting the Mesh ID25
- Entering the Room Number26
- Configuring the Equipment Settings27
- Equipment Codes28
- Configuring Energy Savings Settings29
- Setting the Thermostat Clock30
- Testing the Thermostat31
General: Configuration & Managing Accessories32
- Activating a Sensor32
- Paring a Sensor33
- Verifying Sensor Connection Status and Unlinking Sensors34
- Configuring the Functionality of a Sensor35
- Completing the Sensor Setup36
DSS: Unit Specific Installations37
- Installing the HVAC Controller in Friedrich Ductless Split Systems37
- DSS: Thermostat Configuration39
VRP: Unit Specific Installations40
- Installing the Wireless Receiver on a VRP Unit40
- Mouting the Wall Controller of the VRP to the Wall41
- Installing the HVAC Controller in VRP Unit42
- VRP: Thermostat Configuration43
Freshaire PTAC: Unit Specific Installations44
- Wireless Receiver Installation44
- Installing the HVAC Controller for Freshaire PTAC Unit45
- Freshaire PTAC: Thermostat Configuration46
General: Vert-I-Pak / PTAC T-Stat Installation47
General: Custom Energy Savings Settings49
- Accessing the Custom Energy Savings Settings49
- Using the Thermostat Settings Screens50
- Custom Energy Settings Index51
- Fan Control Mode53
- St Stage Differential - Heat54
- Nd Stage Differential - Heat55
- 1St Stage Differential - Cool56
- Incidental Occupancy Threshold57
- Night Occupancy Threshold58
- Forced 2Nd Stage Heating59
- Night Occupancy Start60
- Night Occupancy End61
- Temperature Recovery Time62
- Recovery Temperature - Heat63
- Temperature Setback Delay64
- Minimum Setback Temperature - Heat65
- Maximum Setback Temperature66
- Recovery Temperature - Cool67
- Minimum Set Point68
- Maximum Set Point69
- Temperature Control Mode70
- Auto Changeover Set Point Offset71
- Setback Set Points72
- Auto-Restore73
- The Setting Is Reserved for the Internal Functions74
- Setpoint Overshoot75
- Automatic Humidity Control76
- 2Nd Stage Cool Differential77
- Smart Setback78
- Humidity Control Threshold79
- Humidity Cutoff Temperature80
- The Setting Is Reserved for the Internal Functions81
- Energy Management On/Off82
- 31- Door/Window Shut off Relay83
- 32- Auto Fan Speed 1Nd Stage Differential84
- 33- Auto Fan Speed 2Nd Stage Differential85
- Temperature Calibration86
- Automode Type87
- Humidity Control in an Occupied Room88
- Heat Equipment Lockout89
General: Thermostat Maintenance90
- Replacing Thermostat Batteries90
General: Errors91
- Errors that Might Appear91
General: Troubleshooting92
- Restoring Factory Settings92
APPENDIX 1 - Energy Saving Presets93
APPENDIX 2 - Glossary95
- Warranty Information96
Technical Specifications97

Friedrich DSSXEMWRT3 - Warranty Information

Table of Contents

Related product manuals