How to prevent oversudsing in Frigidaire Washer?
If your Frigidaire washer is oversudsing, run a rinse cycle. Use a low-sudsing, high-efficiency detergent. In future loads, use less detergent. This can be caused by using the wrong detergent or using too much detergent.
Why Frigidaire Affinity 6000 won’t spin?
If your Frigidaire washer isn't spinning, make sure the door and dispenser drawer are completely closed. If the load is too small, add one or two similar items to help balance it. The causes of this issue can be an unclosed door, an unclosed dispenser drawer, or a load that is too small.
Why Frigidaire Affinity 6000 is not filling with water?
If your Frigidaire washer isn't filling with water or is filling slowly, first, check another faucet in your house to ensure the water supply is adequate. Wait until the water supply and pressure increase. Fully open both the hot and cold water faucets. Ensure water pressure is at least 30 psi (260 kPa), and avoid running water elsewhere in the house while the washer is filling. Straighten any kinks in the water inlet hoses and clean the inlet screens. The causes could be an inadequate water supply, water supply faucets not fully open, water being used elsewhere in the house, kinked water inlet hoses, or plugged water inlet screens.
What to do if Frigidaire Affinity 6000 water does not drain?
If water in your Frigidaire washer does not drain or drains slowly, clean and straighten the drain hose. The maximum standpipe height is 8’ (2.4 m). This issue is caused by a kinked or clogged drain hose.
How to fix water leaks in Frigidaire Affinity 6000?
If you're experiencing water leaks with your Frigidaire washer, check and tighten the fill hose connections at the faucet or washer. Install the rubber sealing washers provided. If the house drain pipes are clogged, unclog them, or contact a plumber if necessary. This can be caused by a loose fill hose connection or clogged house drain pipes.
How to prevent residue on clothes from Frigidaire Affinity 6000?
If your Frigidaire washer leaves residue or powder on dark items, or makes fabrics feel stiff, try increasing the water temperature to the hottest setting safe for the fabric. Avoid overloading the washer. Consider switching to a liquid detergent or using a non-precipitating water conditioner with your non-phosphate granular detergent. This can be caused by undissolved detergent, the combination of non-phosphate granular detergents with hard water minerals, or overloading the washer.
What causes high pitch “jet engine” noise in Frigidaire Affinity 6000?
This is normal operation of the Frigidaire unit.
What to do with water collecting in Frigidaire Affinity 6000 Washer bleach and fabric softener compartments?
Water may be removed by removing the dispenser drawer and draining water into the empty drum or sink.
How to fix vibrating noise in Frigidaire Affinity 6000?
If your Frigidaire washer is making a vibrating noise, adjust the leveling legs to ensure the washer rests firmly on the floor. Refer to the Installation Section for guidance. Also, check that the shipping bolts and foam blocks have been removed during installation, consulting the Installation Section if needed. If the wash load is unevenly distributed in the drum, stop the washer and redistribute it. This can be caused by the washer not resting firmly on the floor, shipping bolts and foam blocks not being removed, or an unevenly distributed wash load.
Why Frigidaire Washer is making a thumping sound?
If your Frigidaire washer is making a thumping sound, it is usually normal if you have heavy wash loads. However, if the sound persists, stop the washer and redistribute the wash load. This can be caused by heavy wash loads or the washer being out of balance.
Guidelines to prevent injury and damage during appliance repair.
Details on identifying the washer via serial and model number configurations.
Overview of control, drum light, door switch, and door lock assembly functions.
Details on the electronic water level sensor and water inlet valve assembly.
Details on the limited warranty coverage, exclusions, and service procedures.
Tools needed and pre-installation requirements for washer setup.
Specifications for electrical circuits, power supply, and proper grounding.
Physical dimensions of the washer and minimum installation clearance requirements.
Specifications for water supply, drain system, and unpacking procedures.
Instructions for leveling the washer and connecting inlet water hoses.
Steps for installing the washer onto a 15" drawer pedestal accessory.
Visual guide to the control panel buttons, knobs, and indicators for Affinity washers.
Step-by-step guide for operating the washer and selecting wash cycles.
How to adjust wash/rinse temperatures, spin speed, and soil level settings.
How to read error codes, perform diagnostic tests, and clear stored codes.
Comprehensive table listing failure codes, fault conditions, and corresponding checks.
Detailed tests for common electronic components and their circuits.
Important safety warnings and cautions before performing component removal procedures.
Procedures for removing the door strike and the loading door assembly.
Instructions for removing and disassembling the detergent drawer and its components.
Guide to safely removing the electronic control board from the console.
Comprehensive guide to removing the entire tub assembly, including critical sub-steps.
Troubleshooting guide for common issues like blue stains, lint, and fabric damage.
Diagnosing and resolving noises, vibrations, and the washer not starting.
Addressing problems with spinning, draining, water temperature, and filling.
Schematic showing electrical connections for the Affinity 7000 series washer.
Schematic showing electrical connections for the Affinity 6000 series washer.
General| Type | Front Load |
|---|---|
| Capacity | 4.5 cu. ft. |
| Steam Function | Yes |
| Sanitize Cycle | Yes |
| Spin Speed | 1300 RPM |
| Energy Star Certified | Yes |
| Steam Option | Yes |
| Color | White |
| Delay Wash | Yes |
To Next Page