Fujitsu ErgoPro e Series - Specification Tables and Memory Tables

104 pages

To Next Page

To Previous Page

PC Specialist's Handbook ErgoPro e-, x- and s- Series

First Edition, Release 4 - June 1998 Page 81

Section 9 :

Specification tables

Memory tables

Main Page

Default Chapter3
- Default Chapter3
  - Lithium Battery3
  - Table of Contents4
- Disassembling the Units9
2-Slot Assembly/Desassembly Opening & Closing the System Unit Cover10
- Installing and Removing Disk Tray10
- Installing and Removing Mass Memory Devices11
- Removing the Power Supply11
- Replacing the Mother Board12
4-Slot Assembly/Desassembly Opening & Closing the System Unit Cover13
- Removing and Installing the Mass Memory Carriage13
- Installing and Removing Mass Memory Devices14
- Removing the Power Supply14
- Removing the 5.25" Carriage15
6-Slot Assembly/Desassembly Opening & Closing the System Unit Cover16
- Removing the Mass Memory Carriage16
- Removing the Power Supply and Backplane Board17
- Replacing the Motherboard18
Mass Memory Expansion Unit19
- Differing the Main Unit from the Expansion Box19
- Removing the Disk/Power Carriage from the Expansion Unit20
- Expansion Unit Cables20
- Jumper Settings21
System Board22
- Block Diagram22
- System Board Layout23
Force FLASH Load27
- Force Flash Load Pads27
2-Slot PCI/ISA Back Plane AC4163928
4-Slot PCI/ISA Back Plane AC4163828
6-Slot PCI/ISA Back Plane AC4163729
Ethernet Module AC4163529
Matrox Millenium AF31452 Graphic Adapter30
Aztech AF30064 Sound Board30
- System Setup31
Entering Setup32
- Entering SETUP with Passwords32
- Moving Around in SETUP32
- Setting Parameters to Default Values33
- Exiting SETUP34
- Saving Changes and Exiting34
- Exiting Without Saving Changes34
SETUP Screens and Parameters34
- User Menu34
- Admin Menu39
- Info Menu48
- Help Menu48
- Section 4 : Miscellaneous & Hints52
Bios52
- Shadow Option Proms52
- BIOS Modules52
Drivers54
- List of Drivers54
- Video54
Powermaster55
Utilities55
- Video - Ergografix55
- Install.exe55
- ICL Desktop55
- Flash.exe55
- Power Master III Ver 3.155
- Power Master II Ver55
- PMSUSP.SYS (Version 4.00)55
- Pmsuspe.exe55
- APM.SYS (Version 2.0 Needed)55
Tips & Hints56
- Using Memory Managers56
- EMM386 Memory Manager56
- QEMM Memory Manager (Ver 7.5)56
- Using ISA Configuration Utility (ICU)56
- Hard Disk Partitioning (DOS 6.X)56
- Section 5 : Power-On Test & Error Indications58
Power on Self Test (POST)58
- Two Long Beeps and a Message58
- Sequences of Four or Eight Beeps63
- Sequences of Five Beeps64
BIOS Check Points65
Audio70
Floppy Disk Controller70
Serial Port Communication70
Parallel Port Communication71
PCI Bus Enhanced IDE Interface71
Keyboard & Mouse71
Video71
- Refresh Rates72
Network73
Peripheral Component Interconnect (PCI Interface)73
Instant on73
LED Board73
- Pin Assignments75
Serial Ports76
Parallel Port (Standard Mode)76
Mouse Port77
Keyboard Connector77
RJ45 (Standard Twisted Pair) Ethernet Port78
AUI Ethernet Port78
VGA-Type Connector79
VGA Pass-Through Connector on System Board80
ISA Bus Connector81
PCI Bus Connector82
SCSI Port Connector83
Audio Connector84
- Speaker Type Connector84
- Microphone Type Connector84
- Section 8 : Machines Identification85
E-, X- and S- Series : Stucture Code86
Identification Codes87
- Specification Tables and Memory Tables89
Machine Specifications90
System Memory Map92
Memory Configurations92
SIMM Recommendations93
Channels, Addresses and Timer Counters94
- DMA Channels94
- Interrupt Levels95
- I/O Addresses96
- Timer97
- Real-Time Clock (RTC) and CMOS RAM97
Power Supply Characteristics98
- Air Circulation98
- Power Consumption98
- Section 10 : Spare Parts Table99
Spare Parts100

Fujitsu ErgoPro e Series - Specification Tables and Memory Tables

Table of Contents

Related product manuals