A switch connection example is shown below.
# Copyright (c) 2003-2007 Emulex. All rights reserved.
#
# Solaris LightPulse lpfc (SCSI) / lpfn (IP) driver: global initialized data.
#
# lpfc.conf 1.54 2007/11/21 12:00:49PST
# Verbosity: only turn this flag on if you are willing to risk being
# deluged with LOTS of information.
# You can set a bit mask to record specific types of verbose messages:
#
# 0x1 ELS events
# 0x2 Device Discovery events
# 0x4 Mailbox Command events
# 0x8 Initialization events
# 0x10 Link Attention events
# 0x20 IP events
# 0x40 FCP events
# 0x80 Node table events
# 0x400 Miscellaneous events
# 0x800 SLI events
# 0x2000 IOCtl events
# 0x4000 FCP Residual Underrun events
# 0xffff Log All Events
log-verbose=0x0;
# Setting log-only to 0 causes log messages to be printed on the
# console and to be logged to syslog (which may send them to the
# console again if it's configured to do so).
# Setting log-only to 1 causes log messages to go to syslog only.
log-only=1;
# standalone parameters for fc-sp are used globally.
#
enable-auth=0;
# LWWN|RWWN|auth_tov|auth_mode|bi-dir|typelist|hashlist|dhgplist|reauth_intval
# typelist=dhchap:fcap:fcpap:kerberos
# hashlist=sha1:md5
# dhgplist=1536:null:1024:1280:2048
# For example:
# The first entry is for host-to-fabric, the second entry is for end-to-end
# auth-cfgparms="0000000000000000|FFFFFFFFFFFFFFFF|002d|02|01|01000000|02010000|040
1020305000000|0000012c";
# LWWN:type:length:pwd:RWWN:type:length:pwd
# type: 0001 ASCII 0002 Binary
# length: length of password in hex
# For example:
# auth-keys="20000000C9365947:0001:0100:11223344556677881122334455667788:2000000DEC
03ED80:0001:0100:aabbccddeeffgghhaabbccddeeffgghh";
#
# +++ Variables relating to FCP (SCSI) support. +++
#
# specifies the method of binding to be used. This
# binding method is used for persistent binding and automaped
# binding. A value of 1 will force WWNN binding, value
# of 2 will force WWPN binding, value of 3 will force
# DID binding and value of 4 will force the driver to derive
# binding from ALPA (hard addressed) in a private loop environment.
# Any persistent binding whose type does not match with the
# bind method of the port will be ignored.
#fcp-bind-method=2;
lpfc0-fcp-bind-method=2;
lpfc1-fcp-bind-method=2;
For direct connections, lpfc0-fcp-bind-method=4;
# Setup FCP persistent bindings,
# fcp-bind-WWPN binds a specific WorldWide PortName to a target id,
# fcp-bind-WWNN binds a specific WorldWide NodeName to a target id,
# fcp-bind-DID binds a specific DID to a target id.
# Binding method must match with the bind method of that HBA, else the
# binding will be ignored.
# fcp-bind-method should NOT be set to 4 when one of these binding methods
# is used.
# WWNN, WWPN and DID are hexadecimal values.
# WWNN must be 16 digit BCD with leading 0s.
# WWPN must be 16 digit BCD with leading 0s.
# DID must be 6 digit BCD with leading 0s.
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris
To Next Page
Loading...
