FUTABA 32MZ-WC - FLT. Expert (AileronElevator Gyro Expert Setting); (1) HeadHld A HeadHld E: Head hold aileron elevator; (2) StopTune A: Stop tune aileron; (3) StopTune E: Stop tune elevator

216
＜
Model Menu (Helicopter)
＞
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
+(/,&237(5
FLT.Expert（Aileron/ElevatorGyroExpertSetting）
FLT.Expert（Aileron/ElevatorGyroExpertSetting）
The
"
FLT.EXPERT
"
PHQXVDOORZIXUWKHUUH¿QHPHQWRIF\FOLFJ\URSHUIRUPDQFH
"
FLT. EXPERT
"
screen from the
"
EXPERT MENU 3D
"
screen.
(1) HeadHld A / HeadHld E: Head hold aileron / elevator
Thisfeaturesisusedtoadjusttheheadingholdaspectofthegyrocon-
trol.Ifthehelicopterisnotholdingangleorcycliccontrolrates,increas-
ingtheheadingholdgainwillimproveholdingthehelicopteratacertain
angleandimprovethecyclicrateconsistency.Ifthisissettoohighyou
couldseeanoscillationonthataxis.Loweringtheheadingholdbelow
defaultwouldbeusedifthetransmittergainisreducedandaconsistent
oscillationisstillnotfixedduringflight.
Settingranges:0~200%Initialvalue:80%
(2) StopTune A : Stop tune aileron
Cyclicstoptuningonthe aileronaxis. Ifthehelicoptercontinuesto coast
afteranafteranailroll,lowering"StpTuneA"willcreateaharderstopaction
toremovethecoasting.Ifthehelicopterbouncesontheaileronaxisafter
anaileroncontrolinput,increasing"StpTuneA"willreducethisbounce.
Settingranges:0~250%Initialvalue:80%
(3) StopTune E: Stop tune elevator
Cyclicstoptuningontheelevatoraxis.Ifthehelicopter,afteranelevator
flip,continuesto coast,lowering"StopTuneE"willcreateaharderstop
actiontoremovethecoasting.Ifthehelicoptercontinuestocoastafter
anelevatorflip,loweringthe"StoptuneE"willreducethisbounce.
Settingranges:0~250%Initialvalue:80%
(4) HeadResp: Head Response
HeadResponsematchesthegyrocontrolspeedtothatwhichthe heli-
copteriscapableofreacting.InastandardhelicopteraHeadResponse
of1shouldalwaysbeused,butonsomescaleapplications,oruniquely
designedrotorheads,increasingheadresponsemightbeneededtocure
overcorrectionofthegyro.
Settingranges:1~10Initialvalue:1
(5) DeadBand: Dead band
Transmittercontroldeadband.Ifyouarenoticinginconsistentswash
platedriftorpoorinitializationit couldbepoor transmitterpotentiom
-
eterresolution.Ifyouhavetoincreasethisvaluebeyond10.0,itisbest
tocheckcalibrationonyourtransmitter.
Settingranges:0~25Initialvalue:4.0
Cond
Cond
Cond
Cond
(6) RESET : FLT tune data reset
Thisresetsthe"FLT.Tun"settingbacktothedefaults.