To Next PageTo Next PageTo Previous PageTo Previous Page
What to do if GAGEMAKER MIC TRAC MT-3000 Measuring Instruments setting blocks do not make contact?
If the setting blocks don't make contact, there might be debris between them. Remove, clean, and reinstall the blocks to ensure proper contact.
What to do if the printer does not function on GAGEMAKER MIC TRAC MT-3000 Measuring Instruments?
If your GAGEMAKER Measuring Instruments printer does not function, start by checking the cables to ensure they are properly connected and undamaged. If the cables are fine, verify that the printer power switch is turned on.
What to do if CPU display does not change when adjustment knobs are turned on GAGEMAKER MIC TRAC MT-3000?
If the CPU display of your GAGEMAKER Measuring Instruments does not change when you turn the adjustment knobs, first check if the locks are engaged and loosen the locking knob. Then, inspect the cables for any damage or improper connections. Also, consider that you might be at the end of travel.
What to do if the printer paper does not advance in GAGEMAKER MIC TRAC MT-3000?
If the printer paper of your GAGEMAKER Measuring Instruments does not advance, first check if the unit is out of paper and refill it. If paper is loaded, ensure that the paper is fed correctly, re-feeding if necessary.
What to do if the movable block does not move when the handle is turned on GAGEMAKER MIC TRAC MT-3000?
If the movable block of your GAGEMAKER Measuring Instruments does not move when the handle is turned, the locking knob may be engaged. Loosen the locking knob to allow movement.
What to do if the CPU will not zero on GAGEMAKER Measuring Instruments?
If your GAGEMAKER Measuring Instruments CPU will not zero, check the cables to ensure they are not damaged and are properly connected.
What does it mean when GAGEMAKER Measuring Instruments DRO display reads “CALIBRATION ERROR” when powered on?
If the DRO display shows “CALIBRATION ERROR” when powered on, it could be due to a loose or missing Force cable, or the brake might be locked with a load applied to the moving anvil. Check the cable and its connections. Unlock the brake and make sure the moving anvil is moving freely and is in a neutral position.
What to do if GAGEMAKER Measuring Instruments movable block does not move when the handle is turned?
If the movable block doesn't move when you turn the handle, the locking knob might be engaged. Loosen the locking knob to allow movement.
Why GAGEMAKER MIC TRAC MT-3000 DRO will not zero?
If the DRO won't zero, the cables may be damaged or not properly connected. Inspect the cables to ensure they are in good condition and securely connected.
What to do if GAGEMAKER MIC TRAC MT-3000 Measuring Instruments DRO display does not change when adjustment knobs are turned?
If the DRO display doesn't change when you turn the adjustment knobs, check if the locks are engaged, or if the cables are damaged or not properly connected. Also, check if you are at the end of travel. To fix this, loosen the locking knob, check the cables, and traverse the movable block.
General| Brand | GAGEMAKER |
|---|---|
| Model | MIC TRAC MT-3000 |
| Category | Measuring Instruments |
| Language | English |
Defines the MIC TRAC as an electronic calibration and measurement center for part inspection and gage calibration, detailing its capabilities.
Explains Gagemaker's perspective on accuracy, emphasizing environmental factors like temperature and humidity.
Provides contact details including phone number and operating hours for Gagemaker customer support.
Directs users to the Gagemaker website for obtaining the latest product information and software updates.
Details and illustrates specific components of the MIC TRAC, covering parts like receiver pads and adjustment knobs.
Describes the primary components of the DRO screen, including the status bar, position display, and message line.
Explains the operation and functions of the DRO's softkeys across different pages for user interaction.
Provides step-by-step instructions for removing and replacing lifting lugs on the MIC TRAC unit.
Guides users on the correct method for measuring parts using the MIC TRAC with the Force-Lok feature engaged.
Offers essential tips for maintaining the MIC TRAC, including lubrication, proper usage surfaces, and environmental care.
Clarifies that the unit has no user-serviceable parts and outlines requirements for calibration and proper shipping.
Details crucial safety precautions for operating the MIC TRAC, covering cable management and personal safety.
Explains the process for returning the MIC TRAC for repair or calibration, including obtaining authorization.
