GE 735

GE Power Management
735/737 Feeder Protection Relay i
INDEX
Numerics
50
see entry for PHASE INSTANTANEOUS OVERCURRENT
50G/50N
see entry for GROUND INSTANTANEOUS OVERCURRENT
51
see entry for PHASE TIME OVERCURRENT
51G/51N
see entry for GROUND TIME OVERCURRENT
A
ACCESSORIES
............................................................. 1-5
ACTUAL VALUES
........................................................ 3-14
readin
g
with Modbus
.................................................... 4-5
ANSI CURVES
....................................................... 5-1, 5-2
ANSI EXTREMELY INVERSE CURVES
..................... 5-8, 5-9
ANSI MODERATELY INVERSE CURVES
.................. 5-2, 5-3
ANSI NORMAL INVERSE CURVES
.......................... 5-4, 5-5
ANSI VERY INVERSE CURVES
............................... 5-6, 5-7
AUTORECLOSE
.......................................................... 3-10
B
BACKUP WIRING
core balance
............................................................... 2-7
residual
..................................................................... 2-7
BLOCK DIAGRAM
......................................................... 1-4
BLOCK INSTANTANEOUS ON AUTORECLOSE
.............. 3-10
BURDEN
...................................................................... 1-6
BUSY, REJECTED MESSAGE ERROR
............................ 4-9
C
CLEAR TRIP RECORD
................................................ 3-14
COMMANDS
.......................................................3-14, 3-15
Modbus
...................................................................... 4-6
COMMISSIONING
......................................................... 7-1
COMMUNICATIONS
description
................................................................. 2-8
electrical interface
....................................................... 4-1
errors
........................................................................ 4-9
memory map
............................................................. 4-10
multi-channel relayin
g
................................................ 2-10
overview
.................................................................... 4-1
RS485
....................................................................... 2-9
slave address
............................................................. 4-2
software
................................................................... 3-12
switch settin
g
s
............................................................ 3-8
testin
g
................................................................ 6-1, 6-4
timin
g
........................................................................ 4-2
CONTROL POWER
....................................................... 1-7
description
............................................................... 2-11
CONTROLS
.................................................................. 3-2
CORE BALANCE BACKUP WIRING
................................. 2-7
CRC-16
ALGORITHM
....................................................... 4-2, 4-3
CT BURDEN
................................................................. 1-6
CTs
600/5
....................................................................... 3-16
description
................................................................. 2-8
specifications
............................................................. 1-6
CURRENT INDICATORS
................................................ 3-7
CURRENT SIMULATION
......................................3-12, 3-14
CURRENT TRANSFORMERS
see CTs
CURVE SHAPE CONTROLS
........................................... 3-2
CURVES
...................................................................... 5-1
CUSTOM SCHEME
..............................................3-10, 3-14
D
DATA FORMATS FOR MEMORY MAP
............................4-12
DATA FRAME FORMAT
................................................. 4-1
DATA FRAME RATE
...................................................... 4-1
DATA PACKET FORMAT
................................................ 4-2
DEFINITE TIME CURVES
.....................................5-10, 5-11
DESCRIPTION
...............................................1-2, 5-1, 5-10
DIAL SIMULATION
.......................................................3-14
DIELECTRIC STRENGTH TESTING
...............................2-12
DIMENSIONS
............................................................... 2-1
DISABLE TRIP RELAYS
................................................3-14
DRAWOUT RELAY
........................................................ 2-3
E
ELECTRICAL INSTALLATION
......................................... 2-5
ENABLE TRIP RELAYS
.................................................3-14
ENVIRONMENTAL SPECIFICATIONS
.............................. 1-8
ERROR CHECKING
....................................................... 4-3
ERROR RESPONSES
.................................................... 4-9
F
FEATURES
.................................................................. 1-1
FILE MENU
.................................................................3-15
FREQUENCY
................................................................ 3-9
FRONT PANEL
............................................................. 3-1
G
GROUND CURRENT ACCURACY
.............................6-1, 6-4
GROUND INSTANTANEOUS OVERCURRENT
curve shape
............................................................... 3-4
level
.......................................................................... 3-5
multiplier
.................................................................... 3-5
multiplier shift
............................................................. 3-9
pickup
.................................................................3-4, 3-6
pickup test
................................................................. 6-1
shape
........................................................................ 3-4
timin
g
test
.................................................................. 6-3
trip
............................................................................ 3-5
trip shape
................................................................... 3-7
GROUND OVERCURRENT
see entries for GROUND TIME and GROUND
INSTANTANEOUS OVERCURRENT
GROUND TIME OVERCURRENT
curve shape
............................................................... 3-4
multiplier
.................................................................... 3-5
multiplier shift
............................................................. 3-9
pickup
.................................................................3-4, 3-6
shape
........................................................................ 3-4
specifications
............................................................. 1-6
trip
......................................................................3-6, 3-7