gefran AFE200 Series

116 AFE200 • Instruction Manual
16_H Receives 16 bits from FB and copies to 16H bit of monitor. OK
16_L Receives 16 bits from FB and copies to 16L bit of monitor. OK
A Fieldbus M->S X Mon parameter can only be assigned to a single “src”. If assigned
to more than one src, an error signal is generated during eldbus initialization.
Menu PAR Description UM Type FB BIT Def Min Max Acc
14.3.4 4026 FIeldbus M->S1 div FLOAT 1.0 1.0 1000.0 ERW
14.3.8 4036 FIeldbus M->S2 div FLOAT 1.0 1.0 1000.0 ERW
14.3.12 4046 FIeldbus M->S3 div FLOAT 1.0 1.0 1000.0 ERW
14.3.16 4056 FIeldbus M->S4 div FLOAT 1.0 1.0 1000.0 ERW
14.3.20 4066 FIeldbus M->S5 div FLOAT 1.0 1.0 1000.0 ERW
14.3.24 4076 FIeldbus M->S6 div FLOAT 1.0 1.0 1000.0 ERW
14.3.28 4086 FIeldbus M->S7 div FLOAT 1.0 1.0 1000.0 ERW
14.3.32 4096 FIeldbus M->S8 div FLOAT 1.0 1.0 1000.0 ERW
14.3.36 4106 FIeldbus M->S9 div FLOAT 1.0 1.0 1000.0 ERW
14.3.40 4116 FIeldbus M->S10 div FLOAT 1.0 1.0 1000.0 ERW
14.3.44 4126 FIeldbus M->S11 div FLOAT 1.0 1.0 1000.0 ERW
14.3.48 4136 FIeldbus M->S12 div FLOAT 1.0 1.0 1000.0 ERW
14.3.52 4146 FIeldbus M->S13 div FLOAT 1.0 1.0 1000.0 ERW
14.3.56 4156 FIeldbus M->S14 div FLOAT 1.0 1.0 1000.0 ERW
14.3.60 4166 FIeldbus M->S15 div FLOAT 1.0 1.0 1000.0 ERW
14.3.64 4176 FIeldbus M->S16 div FLOAT 1.0 1.0 1000.0 ERW
The Div M->Sx eldbus parameters can be used to increase the resolution of the
datum sent on the bus to the drive in the corresponding channel in EU and EU_oat
exchange mode. The parameter value is used by the drive as the divider of the incom-
ing datum, so that a number with decimal digits can be transferred.
Note! You must check the size in bits of the datum that is sent to make sure that the maximum value in bits
fits in a 16-bit integer. For example, if specifying the divider as “Fieldbus M->Sn div” = 1000, the
maximum value that can be used for the exchanged datum is 32.768 (32768/1000).
I.e. : FIeldbus M->S1 div = 10, Fieldbus S->M1 ipa = Ramp ref src 1, Fieldbus
M->S1 sys = Eu. If the PLC sends the decimal value 1000 on the rst word the value
of DC voltage ref src on the drive is 1000/10 = 100.
14.4 - COMMUNICATION/FIELDBUS S2M
Menu PAR Description UM Type FB BIT Def Min Max Acc
14.4.1 4180 Fieldbus S->M1 ipa FBM2SIPA 0 0 20000 RW
14.4.5 4190 Fieldbus S->M2 ipa FBM2SIPA 0 0 20000 RW
14.4.9 4200 Fieldbus S->M3 ipa FBM2SIPA 0 0 20000 RW
14.4.13 4210 Fieldbus S->M4 ipa FBM2SIPA 0 0 20000 RW
14.4.17 4220 Fieldbus S->M5 ipa FBM2SIPA 0 0 20000 RW
14.4.21 4230 Fieldbus S->M6 ipa FBM2SIPA 0 0 20000 RW
14.4.25 4240 Fieldbus S->M7 ipa FBM2SIPA 0 0 20000 RW