English (GB)
51
Grundfos GO and wireless pump connection
1. Power on both pumps.
2. Establish contact to one of the pumps with
Grundfos GO.
3. Set the needed analog and digital inputs via
Grundfos GO according to the connected
equipment and the required functionality. See
section 13.41 Assisted pump setup.
4. Assign a pump name to the pump using Grundfos
GO. See section 13.35 "Pump name".
5. Disconnect Grundfos GO from the pump.
6. Establish contact to the other pump.
7. Set the needed analog and digital inputs via
Grundfos GO according to the connected
equipment and the required functionality. See
section 13.41 Assisted pump setup.
8. Assign a pump name to the pump using Grundfos
GO. See section 13.35 "Pump name".
9. Select the "Assist" menu and "Multipump setup".
10. Select the desired multipump function. See
sections 13.43.1 Alternating operation,
13.43.2 Backup operation and 13.43.3 Cascade
operation.
11. Press [>] to continue.
12. Set the time for pump changeover such as the
time at which the alternation between the two
pumps is to take place. This step applies only if
you have selected "Alternating operation, time"
and if the pumps are fitted with FM 300.
13. Press [>] to continue.
14. Select "Radio" as the communication method to
be used between the two pumps.
15. Press [>] to continue.
16. Press "Select pump 2".
17. Select the pump from the list.
Use the [OK] or button to identify the pump.
18. Press [>] to continue.
19. Confirm the multipump setup by pressing [Send].
20. Press [Finish] in the "Setup complete" dialog box.
21. Wait for the green indicator light in the middle of
Grundfos Eye to light up.
The multipump system has now been set.
Grundfos GO and wired pump connection
1. Connect the two pumps with each other with a
3-core screened cable between the GENIbus
terminals A, Y, B.
2. Power on both pumps.
3. Establish contact to one of the pumps with
Grundfos GO.
4. Set the needed analog and digital inputs via
Grundfos GO according to the connected
equipment and the required functionality. See
section 13.41 Assisted pump setup.
5. Assign a pump name to the pump using Grundfos
GO. See section 13.35 "Pump name".
6. Assign pump number 1 to the pump. See section
13.23 "Number" (Pump number).
7. Disconnect Grundfos GO from the pump.
8. Establish contact to the other pump.
9. Set the needed analog and digital inputs via
Grundfos GO according to the connected
equipment and the required functionality. See
section 13.41 Assisted pump setup.
10. Assign a pump name to the pump using Grundfos
GO. See section 13.35 "Pump name".
11. Assign pump number 2 to the pump. See section
13.23 "Number" (Pump number).
12. Select the "Assist" menu and choose "Multipump
setup".
13. Select the desired multipump function. See
sections 13.43.1 Alternating operation,
13.43.2 Backup operation and 13.43.3 Cascade
operation.
14. Press [>] to continue.
15. Set the time for pump changeover such as the
time at which the alternation between the two
pumps is to take place. This step applies only if
you have selected "Alternating operation, time"
and if the pumps are fitted with FM 300.
16. Press [>] to continue.
17. Select "BUS cable" as the communication
method to be used between the two pumps.
18. Press [>] to continue.
19. Press "Select pump 2".
20. Select the additional pump from the list.
Use the [OK] or button to identify the
additional pump.
21. Press [>] to continue.
22. Press [Send].
23. Press [Finish] in the "Setup complete" dialog box.
24. Wait for the green indicator light in the middle of
Grundfos Eye to light up.
The multipump system has now been set.
To Next Page
Loading...
