Grundfos TPE Series - Page 76

76 pages

To Previous Page

www.grundfos.com

98476024 1018

ECM: 1246569

Trademarks displayed in this material, including but not limited to Grundfos, the Grundfos logo and “be

Main Page

Default Chapter2
- Table of Contents2
1 Symbols Used in this Document3
2 Abbreviations and Definitions4
3 General Information4
4 General Description4
- Radio Communication4
- Battery4
5 Receiving the Product5
- Transporting the Product5
- Inspecting the Product5
6 Mechanical Installation5
- Handling the Product5
- Mounting the Product5
- Cable Entries5
- Ensuring Motor Cooling5
- Outdoor Installation6
- Drain Holes6
7 Electrical Installation6
- Protection against Electric Shock, Indirect Contact7
- Cable Requirements7
- Mains Supply7
- Additional Protection9
- Connection Terminals9
- Signal Cables11
- Bus Connection Cable12
8 Operating Conditions12
- Maximum Number of Starts and Stops12
- Alternating Operation of Twin-Head Pumps12
- Ambient Temperature12
- Installation Altitude13
- Humidity13
- Motor Cooling13
9 User Interfaces13
10 Standard Control Panel14
- Setpoint Setting14
11 Advanced Control Panel16
- Home Display17
- Startup Guide17
- Menu Overview for Advanced Control Panel18
12 Grundfos GO22
- Communication22
- Menu Overview for Grundfos GO23
13 Description of Functions26
- Setpoint26
- Operating Mode26
- Set Manual Speed26
- Set User-Defined Speed26
- Control Mode27
- Proportional-Pressure Setup32
- Analog Inputs32
- Built-In Grundfos Sensor33
- Pt100/1000 Inputs33
- Digital Inputs34
- Digital Inputs/Outputs35
- Signal Relays 1 and 2" (Relay Outputs)37
- Analog Output37
- Controller" ("Controller Settings")38
- Operating Range40
- External Setpoint Function40
- Limit-Exceeded Function43
- Pulse Flowmeter Setup44
- Ramps44
- Standstill Heating44
- Motor Bearing Monitoring44
- Service45
- Number" (Pump Number)45
- Radio Communication" (Enable/Disable Radio Comm.)45
- Language45
- Date and Time" (Set Date and Time)45
- Unit Configuration" (Units)46
- Buttons on Product" (Enable/Disable Settings)46
- Delete History46
- Define Home Display46
- Display Settings46
- Store Settings" (Store Actual Settings)46
- Recall Settings" (Recall Stored Settings)47
- Undo47
- Pump Name47
- Connection Code47
- Run Start-Up Guide48
- Alarm Log48
- Warning Log48
- Assist48
- Assisted Pump Setup48
- Setup, Analog Input49
- Multipump Setup" (Setup of Multi-Pump System)49
- Description of Control Mode53
- Assisted Fault Advice53
14 Selection of Control Mode54
15 Bus Signal55
16 Priority of Settings56
17 Grundfos Eye57
18 Signal Relays58
19 Installing a Communication Interface Module59
20 Identification of Functional Module61
21 Identification of Control Panel61
22 Changing the Position of the Control Panel62
23 Servicing the Product63
- Motor63
- Pump63
24 Cleaning the Product63
25 Megging63
26 Technical Data, Single-Phase Motors63
- Supply Voltage63
- Leakage Current63
27 Technical Data, Three-Phase Motors64
- Supply Voltage64
- Leakage Current, AC64
28 Inputs and Outputs65
29 Other Technical Data66
- Torques67
- Sound Pressure Level68
30 Factory Settings69
31 Disposing of the Product70

Grundfos TPE Series - Page 76

Table of Contents

Other manuals for Grundfos TPE Series

Related product manuals