Need help?Do you have a question about the Hanna Instruments HI9829 and is the answer not in the manual?
General| Type | Portable |
|---|---|
| Parameters Measured | pH, ORP, Conductivity, TDS, Salinity, Resistivity, Dissolved Oxygen, Temperature, Atmospheric Pressure, Turbidity |
| pH Resolution | 0.01 |
| ORP Resolution | 1 mV |
| ORP Accuracy | ±1 mV |
| Conductivity Accuracy | ±1% of reading |
| TDS Accuracy | ±1% of reading |
| Salinity Resolution | 0.01 ppt |
| Salinity Accuracy | ±1% of reading |
| Dissolved Oxygen Resolution | 0.01 mg/L |
| Temperature Resolution | 0.1 °C |
| Atmospheric Pressure Range | 450 to 850 mmHg |
| Atmospheric Pressure Resolution | 1 mmHg |
| Turbidity Accuracy | ±2% of reading |
| Data Logging | Yes |
| Connectivity | USB |
| IP Rating | IP67 |
| Category | Multiparameter |
| pH Accuracy | ±0.02 pH |
| ORP Range | -2000 to 2000 mV |
| Conductivity Resolution | 0.01 mS/cm |
| Salinity Range | 0.00 to 70.00 ppt |
| Dissolved Oxygen Accuracy | ±1.5% of reading |
| Temperature Accuracy | ±0.15°C |
| Atmospheric Pressure Accuracy | ±3 mmHg |
| Turbidity Range | 0 to 4000 NTU |
| Turbidity Resolution | 0.01 NTU |
| Display | LCD with backlight |
| Logging Memory | 45, 000 |
| Power Supply | Rechargeable Lithium-ion battery |
| TDS Resolution | 0.01 ppm to 0.1 ppt |
Check instrument for damage after shipping and save packing materials.
Overview of the HI9829 multiparameter system and its features.
Explanation of the meter's LCD screen and control buttons.
Guide to connecting sensors and probes to the HI9829 meter.
Instructions on how to operate the meter in measurement, logging, and setup modes.
How to access context-sensitive help for the displayed screen.
Measurement range, resolution, accuracy, and calibration for temperature.
Specifications for pH and millivolt measurements, including calibration.
Specifications for Oxidation-Reduction Potential (ORP) measurements and calibration.
Specifications for Dissolved Oxygen measurements and calibration.
Specifications for conductivity measurements, including range and resolution.
Specifications for resistivity measurements, including range and resolution.
Specifications for Total Dissolved Solids measurements, including range and resolution.
Specifications for salinity measurements, including range and accuracy.
Specifications for seawater sigma measurements.
Specifications for turbidity measurements, including range and accuracy.
Specifications for Ammonium Ion Selective Electrode measurements.
Specifications for chloride measurements, including range and accuracy.
Specifications for nitrate-nitrogen measurements, including range and accuracy.
Specifications for atmospheric pressure measurements.
Technical details of the HI9829 meter itself, including memory and interface.
Estimated battery life for the meter under various conditions.
Environmental and physical specifications for the non-logging probe.
Environmental and physical specifications for the logging probe.
Battery life details for the logging probe based on logging interval.
Detailed description of each sensor type compatible with the HI9829 probe.
Procedures for preparing and activating pH, ORP, DO, EC, and ISE sensors.
Step-by-step guide for installing sensors into the multiparameter probe.
Instructions for installing rechargeable or alkaline batteries into the meter.
Steps for powering on the meter and understanding the probe status screen.
How to enable or disable measurement parameters on the meter.
Configuration of measurement units for temperature, TDS, DO, pressure, etc.
Setting temperature coefficients and TDS factors for accurate measurements.
How to use software averaging to stabilize readings.
Specific settings for turbidity averaging to reduce noise.
Performing single-point calibration for pH, conductivity, and dissolved oxygen.
Detailed steps for pH calibration using buffer solutions.
Procedure for calibrating Ion Selective Electrodes (ISE) for various ions.
Guide to performing ORP calibration for accurate redox potential measurements.
Steps for calibrating Dissolved Oxygen sensors, including % saturation and concentration.
Procedures for calibrating conductivity, absolute conductivity, and salinity.
Instructions for performing multi-point turbidity calibration.
How to perform single-point temperature calibration for accuracy.
Guide to calibrating the atmospheric pressure sensor.
Configuring meter settings like time, date, auto power-off, and beep settings.
Setting up probe identification, password, and restoring factory settings.
Viewing and managing stored GPS locations and nearby points.
Option to delete all stored GPS location data.
Enabling power saving mode for the GPS unit to conserve battery.
Displaying current GPS status, coordinates, and satellite information.
Viewing meter information like battery level, firmware, and serial number.
Checking the status of the connected probe and its sensors.
Accessing Good Laboratory Practice data for calibration history.
Options for logging data directly on the meter.
Capabilities for logging data independently on the probe.
Overview of the navigation within the logging menu.
Detailed steps for initiating and managing meter logs.
Setting up and starting logging operations on the probe.
Viewing and managing recorded data logs from the meter or probe.
Adding remarks and managing tag information for logged data.
Instructions for downloading and installing the PC application software.
Connecting the meter to a PC for data transfer.
Connecting the probe to a PC for data transfer.
Solution for when the meter's memory is full.
Troubleshooting low power supply to the probe.
Diagnosing power faults related to the probe cable connection.
Resolving issues with missing language files.
Troubleshooting communication errors with the GPS unit.
Addressing low battery warnings and automatic meter shutdown.
Correcting battery type selection errors.
Troubleshooting low battery issues for logging probes.
Steps to take when meter user data becomes corrupted.
Routine checks and cleaning for sensors and connectors.
Specific care instructions for pH and pH/ORP sensors.
Maintenance procedures for the Dissolved Oxygen sensor membrane and electrolyte.
Cleaning guidelines for EC sensors to ensure performance.
Maintenance for EC/Turbidity sensors, including optical window care.
Care and cleaning instructions for Ion Selective Electrode sensors.
Best practices for installing the probe in various water bodies.
Detailed information on the Ammonium ISE sensor and its applications.
Details on the Chloride ISE sensor, its specifications, and interferences.
Information about the Nitrate ISE sensor, its performance, and interferences.
List of meter models and their included accessories.
Catalog of probes available for purchase separately.
Catalog of complete meter and probe kits.
List of available sensor models for the HI9829 system.
To Next Page