Hardy Instruments A Series

To Next Page

To Previous Page

Table of Illustrations

CHAPTER 3 - INSTALLATION - - - - - - - - - - - - - - - - - - -3-1

POSITIONING THE MODULE FOR INSTALLATION - - - - - - - -3-2

MODULE RELEASE(S)- - - - - - - - - - - - - - - - - - - - - - -3-3

MODULE INSTALLED IN CHASSIS- - - - - - - - - - - - - - - - -3-3

HI 1756-WS WITH DOOR OPEN - - - - - - - - - - - - - - - - - -3-5

HI 1756-2WS WITH DOOR OPEN - - - - - - - - - - - - - - - - -3-5

INDUSTRY STANDARD LOAD CELLS WIRING DIAGRAM - - - - -3-6

HARDY LOAD SENSOR/C2 WIRING DIAGRAM - - - - - - - - - -3-6

REMOTE TERMINAL ASSEMBLY - - - - - - - - - - - - - - - - -3-7

RTA WITH JUMPERS FOR LOAD CELLS WITHOUT

SENSE LINES - - - - - - - - - - - - - - - - - - - - - - - - - - -3-7

RTA CABLE ASSEMBLY - HI 1756WS SINGLE CHANNEL - - - - -3-8

RTA CABLE SCHEMATIC - HI 1756WS SINGLE CHANNEL - - - -3-8

RTA CABLE ASSEMBLY - HI 17562WS DUAL CHANNEL - - - - -3-8

RTA CABLE SCHEMATIC - HI 1756-2WS DUAL CHANNEL- - - - -3-9

HARDY HI 215IT JUNCTION BOX WIRING DIAGRAM - - - - - - -3-9

CHAPTER 4 - SETUP - - - - - - - - - - - - - - - - - - - - - - -4-1

MODULE LEDS SINGLE CHANNEL - - - - - - - - - - - - - - - -4-1

MODULE LEDS DUAL CHANNEL‘ - - - - - - - - - - - - - - - - -4-1

COMMUNICATION CONFIGURATION DIALOG BOX - - - - - - - -4-3

DISCRETE DATA - - - - - - - - - - - - - - - - - - - - - - - - -4-7

PARAMETERS DIALOG BOX - - - - - - - - - - - - - - - - - - -4-10

PARAMETERS DIALOG BOX (CONT’D) - - - - - - - - - - - - - -4-10

MESSAGE CONFIGURATION EXAMPLE- - - - - - - - - - - - - -4-11

CHAPTER 5 - CALIBRATION - - - - - - - - - - - - - - - - - - -5-1

PROPERLY INSTALLED LOAD CELL W/NO BINDING - - - - - - -5-2

MILLIVOLTS/WEIGHT SCALE - - - - - - - - - - - - - - - - - - -5-3

“THE BUTTON” C2 CALIBRATION - HI 1756-WS - - - - - - - - - -5-5

“THE BUTTON” C2 CALIBRATION - HI 1756-2WS - - - - - - - - -5-5

CHAPTER 6 - OPERATING PROCEDURES - - - - - - - - - - - -6-1

COMMUNICATION CONFIGURATION DIALOG BOX - - - - - - - -6-1

DISCRETE DATA - - - - - - - - - - - - - - - - - - - - - - - - -6-2

CHAPTER 7 - TROUBLESHOOTING- - - - - - - - - - - - - - - -7-1

COMMAND RETURN PROCESS - - - - - - - - - - - - - - - - - -7-2

COMMAND DEFINITIONS AND ACTIONS - - - - - - - - - - - - -7-3

MECHANICAL INSPECTION - - - - - - - - - - - - - - - - - - - -7-5

LOAD SHARING AND LOAD SENSOR CHECKOUT - - - - - - - -7-6

Hardy Instruments A Series - Page 7