DAC-42(A)-x-PN
Page 2
DAC-42(A)-x-PN
Manual
Revision: 1.0
22.01.2024
Revision History
R 1.0 22.01.2024
Bm
First edition
Table of Contents
1
Abbreviations ........................................................................................................................................................ 4
2
Terms and Definitions .......................................................................................................................................... 4
3
General information .............................................................................................................................................. 5
3.1
Abstract ................................................................................................................................................................... 5
3.2
Scope ...................................................................................................................................................................... 5
3.2.1
Copyright ..................................................................................................................................................... 6
3.2.2
Documents place of storage ....................................................................................................................... 6
3.2.3
Warning signs, symbols and notes.............................................................................................................. 6
3.2.4
Safety and liability ....................................................................................................................................... 7
3.2.5
General information ..................................................................................................................................... 8
3.3
Terms and conditions .............................................................................................................................................. 9
3.4
Delivery state (default setting) ................................................................................................................................. 9
3.5
Correct product use ................................................................................................................................................ 9
3.6
Non-intended product use ....................................................................................................................................... 9
3.7
Selection and qualification of personnel ................................................................................................................ 10
3.7.1
Inquiries and ordering ............................................................................................................................... 10
3.7.2
Service and repair ..................................................................................................................................... 10
3.7.3
Cleaning, storage, transport ...................................................................................................................... 11
3.7.4
Delivery state (default setting) ................................................................................................................... 11
3.8
Introduction ........................................................................................................................................................... 11
3.9
General Applications ............................................................................................................................................. 11
4
Product overview and description..................................................................................................................... 12
4.1
Technical features ................................................................................................................................................. 12
4.2
Technical data ....................................................................................................................................................... 13
4.2.1
General technical data .............................................................................................................................. 13
4.2.2
Technical data for optional bus interfaces ................................................................................................. 14
4.2.3
Block diagram hardware ........................................................................................................................... 14
4.3
Model code ........................................................................................................................................................... 15
5
Installation ........................................................................................................................................................... 16
5.1
Mounting ............................................................................................................................................................... 16
5.2
Connection ............................................................................................................................................................ 17
5.2.1
General recommendations ........................................................................................................................ 17
5.2.2
Wires and preparation ............................................................................................................................... 17
5.2.3
EMC .......................................................................................................................................................... 18
5.2.4
Specific recommendations for wiring and control cabinets ........................................................................ 18
5.3
Terminal assignment ............................................................................................................................................. 22
5.4
Picture of rear connector ....................................................................................................................................... 22
5.5
Operation modes .................................................................................................................................................. 23
5.6
Wiring diagrams for all operation modes ............................................................................................................... 24
5.6.1
Wiring diagram for operation mode 01 ...................................................................................................... 24
5.6.2
Wiring diagram for operation mode 02 ...................................................................................................... 25
5.6.3
Wiring diagram for operation mode 03 ...................................................................................................... 26
5.6.4
Wiring diagram for operation mode 04 ...................................................................................................... 27
5.6.5
Wiring diagram for operation mode 06 ...................................................................................................... 28
5.6.6
Wiring diagram for operation mode 08 ...................................................................................................... 29
5.6.7
Wiring diagram for operation mode 10 ...................................................................................................... 30
5.6.8
Wiring diagram for operation mode 11 ...................................................................................................... 31
6
Commissioning ................................................................................................................................................... 32
6.1
Front elements ...................................................................................................................................................... 32
6.1.1
DAC-42(A)-x-PN ....................................................................................................................................... 32
6.2
Software block diagrams ....................................................................................................................................... 33
6.2.1
Operation Mode 01; 1 valve with 2 solenoids, open loop .......................................................................... 33
6.2.2
Operation Mode 02; 2 valves with 1 solenoid each, open loop ................................................................. 34
6.2.3
Operation Mode 03; 1 valve with 2 solenoids and spool position feedback .............................................. 35
6.2.4
Operation Mode 04; 1 valve with 2 solenoids and process value feedback .............................................. 36
6.2.5
Operation Mode 06; 1 valve with 2 solenoids spool position feedback and process value feedback ........ 37
6.2.6
Operation Mode 08; 2 valves with 1 solenoid and process value feedback .............................................. 38
6.2.7
Operation Mode 10; stand-alone controller with process feedback ........................................................... 39
6.2.8
Operation Mode 11; stand-alone controller with two process feedbacks .................................................. 40
To Next Page
Loading...