33
Include (Enroll) a Resideo Thermostat
Install Resideo Thermostats according to the manufacturer’s instructions. Device should be mounted in the final location and
tested before adding it to the system.
Note: Resideo is not responsible for property damages due to improper setting of the thermostat modes.
To include a Resideo Thermostat into a Z-Wave network, do the following:
1. At the TUXEDOW Home screen:
a) Touch the Devices and Setup icons to display the “Z-
Wave Device Management” screen.
b) Touch the
ADD DEVICE icon.
2. At the Z-Wave thermostat:
a) Select Thermostat; set the Time/Date.
b) Follow the instructions in the thermostat Installation
Guide for “Z-Wave Inclusion”.
c) To complete inclusion, touch Done.
d) Touch Exit to return to normal operation.
Note: If installing another brand of thermostat,
follow the instructions in the User Guide for that
specific thermostat to include properly into the Z-
Wave network.
Note: Some thermostats do not update temperature
status automatically i.e., Wayne Dalton.
The keypad displays a series of messages:
“Please touch function key on device”
* If not using a Resideo thermostat, inclusion
procedure may vary. Refer to the thermostat
instructions for the inclusion procedure.
The keypad displays a series of messages:
“Please touch function key on device”
“Adding Controller Unit”
“Adding Slave Unit”
“Device added successfully”
Include (Enroll) a Door Lock
Assemble the Z-Wave door lock. NOTE: Be sure the door lock orientation/handedness is correct. Refer to the Door Lock’s
Instruction Guide and connect necessary cables, then install batteries. Include the door lock within 5 ft of the keypad; refer to
the Door Lock’s Instruction Guide for enrollment procedure.
NOTE: Program the user code in the control panel prior to programming that user code into the door lock. User Codes must
be 4-digits.
Enroll a door lock device as follows:
1. At the TUXEDOW Home screen:
a) Touch the Devices icon and then touch the
Setup icon to display the “Z-Wave Device
Management” screen.
b) Touch the ADD DEVICE icon.
2. At the Door Lock:
a) Program the selected user code from the
panel; refer to Door Lock User Guide.
Note: Door lock devices may vary; follow the instructions in the
User Guide for your specific door lock to include properly and to
program a new user code.
The keypad displays a series of messages:
“Please touch function key on device”
“Adding to Security Network”
“Device added successfully”
* Inclusion procedure may vary depending on the door lock
device. Refer to the door lock instructions for inclusion procedure.
Wi-Fi Thermostat Programming
NOTE: Follow the installation guide provided with the Resideo Wi-Fi enabled thermostat to join the Wi-Fi network.
Enrolling
Press Devices > Thermostats (displays Wi-Fi thermostat management page) > Account > enter the Total Connect Comfort
username and password > Save.
NOTE: Enrolling the Wi-Fi thermostat in the TUXEDOW keypad synchronizes it to their Resideo Total Connect 2.0 account.
Enrolling the same Wi-Fi thermostat in Honeywell Home’s Total Comfort app produces a duplicate Wi-Fi thermostat
shown in Resideo Total Connect 2.0 app.
NOTES:
• Account must be configured at:
www.mytotalconnectcomfort.com
• The keypad must be connected to the internet to perform
the association.
• If the account is associated correctly the keypad
displays, “Account associated. Start loading devices.
Please wait…”
• If the account association fails the keypad displays,
“Account association failed. Please try again later.”
• Wi-Fi thermostats are only renamed using the comfort
app/web.
• If using a secondary controller, the user name and
password for MyTotalComfort must be entered.
NOTE: Scenes programmed in the secondary keypad
are local only (will not show up on Total Connect).
• The thermostat must be associated with the primary
controller to use Total Connect Remote services.
• Z-Wave and Wi-Fi thermostats (max. 5) are combined in
automation for a maximum number of 20.
• After successful association the thermostat is
controllable via Total Connect.
• Hold and schedules from MyTotalComfort can’t be
changed from the Tuxedo.
To Next Page
Loading...
Need help?
General
