HySecurity StrongArmPark DCS 14 User Manual

www.hysecurity.com Display Menu D0536 Rev. C 3-5
User Menu Setting Options Menu Tasks & Explanations SDC Wire
Connections
BF 0 (OFF)
Warn Before Operate
0 = off
1 = warning buzzer on
throughout Gate travel
2=warningbuzzeronfor2
secondsofGatetravel
Controlsthewarn-before-operatebuzzerandcanbe
conguredthreeways:
Setto0:Buzzerisdisabled.Thebuzzerwillstillbeep
if alerts, faults, errors, or entrapment occur.
Setto1:Buzzerbeepsfor3secondsbeforegate
moves and continues through entire length of travel.
Setto2:Buzzerbeepsfor3sbeforegatemovesand
continues for 2s of travel.
Notapplicable(N/A)
FA0(OFF)
ForcedOpenAlert
0 = off
1=on
Intended for highly secure facilities.
Setto1,theoperatorsoundsthe3-second“warn
beforeoperate”buzzeralarmandinitiatesaclosure
if the gate is forced open and the closed limit switch
disengages. The motor starts to secure the gate. If
the gate does not fully close within 4s, the motor
turnsoffandthebuzzersoundsfor30seconds.The
displayshowsALERT1-FORCEDOPEN.
N/A
DA0(OFF)
DriftCloseAlert
0 = off (standard)
1=on(detailed)
Setto1,theoperatorsoundsthe3-second“warn
beforeoperate”buzzeralarmandinitiatesanopen
command if the gate is forced, or drifts, off the open
limit switch. The motor starts to reopen the gate. The
motor runs for a maximum of 4s and, if the gate is
notfullyopenattheendofthisperiod,thebuzzer
soundsfor10s.ThedisplayshowsALERT2-DRIFT
CLOSED.
N/A
PE0(OFF)
PhotoEyeAlignment
0 = off
1=on
Setto1,theoperatorservesasanaideinphoto
eyetransmitter/receiveralignment.Thebuzzer
chirps once when the emitter and receiver are not
aligned. When the emitter and receiver are aligned,
thebuzzerchirpstwice.Iftheygooutofalignment
again,thebuzzerwillchirponce.TheAlignment
Mode is reset with a close-limit input or by pressing
the Reset button.
NOTE: If the operator doesn’t run when the power
switch is initially turned ON, check the alignment of
the photo eye and all the photo eye connections.
EYEOpen
EYEClose
EYECOM
CL 0 
Set Clock
0 = Display
1=SetClock
To adjust the hour, minute, day, or month to a
differenttimezone,select1.Oncetheclockisset,
the display returns to the 0 setting.
This feature is useful to read historic operational
data, which can be accessed with a computer via the
USB or RS-232 port.
N/A
LD 5
LCD Contrast
5
0through9
Adjuststhecontrastofthedisplay.Availablesettings
fromlowcontrast0to9highcontrast,withafactory
default setting of 5.
NOTE: While the Operator Status Displays are scroll-
ing, you also have the ability to adjust the contrast by
pressingthePREVandNEXTbuttons.
N/A
US 0
CLEARCOUNT
0 = preprogrammed limit
1=ClearTransientcount
2=ClearTenantcount
3=ClearSpecialcount
4=AllUser
Clearsthelogs(counts)of“usertypes”enteringor
exitingthroughtheStrongArmParkDCgate.This
menu is used most often in Parking lot and revenue
control scenarios. Selecting a number and pressing
SELECTagain,clearsthecount.
COM
TRANSIENTUSER
TENANTUSER
SPECIALUSER

HySecurity StrongArmPark DCS 14 Specifications

General

Brand	HySecurity
Model	StrongArmPark DCS 14
Category	Gate Opener
Language	English