I7910 Payment – User Manual
14 0120-07390-0101
T
T
h
h
e
e
t
t
e
e
r
r
m
m
i
i
n
n
a
a
l
l
i
i
s
s
s
s
p
p
e
e
c
c
i
i
f
f
i
i
e
e
d
d
t
t
o
o
o
o
p
p
e
e
r
r
a
a
t
t
e
e
u
u
n
n
d
d
e
e
r
r
t
t
h
h
e
e
s
s
e
e
c
c
o
o
n
n
d
d
i
i
t
t
i
i
o
o
n
n
s
s
:
:
•
•
T
T
e
e
m
m
p
p
e
e
r
r
a
a
t
t
u
u
r
r
e
e
:
:
+
+
5
5
t
t
o
o
+
+
4
4
0
0
d
d
e
e
g
g
r
r
e
e
e
e
s
s
C
C
e
e
l
l
s
s
i
i
u
u
s
s
(
(
+
+
4
4
0
0
t
t
o
o
+
+
1
1
0
0
4
4
F
F
a
a
h
h
r
r
e
e
n
n
h
h
e
e
i
i
t
t
)
)
•
•
H
H
u
u
m
m
i
i
d
d
i
i
t
t
y
y
:
:
2
2
0
0
%
%
t
t
o
o
9
9
0
0
%
%
r
r
e
e
l
l
a
a
t
t
i
i
v
v
e
e
h
h
u
u
m
m
i
i
d
d
i
i
t
t
y
y
,
,
w
w
i
i
t
t
h
h
n
n
o
o
c
c
o
o
n
n
d
d
e
e
n
n
s
s
a
a
t
t
i
i
o
o
n
n
D
D
o
o
n
n
o
o
t
t
s
s
p
p
i
i
l
l
l
l
l
l
i
i
q
q
u
u
i
i
d
d
s
s
o
o
n
n
t
t
h
h
e
e
s
s
y
y
s
s
t
t
e
e
m
m
c
c
o
o
m
m
p
p
o
o
n
n
e
e
n
n
t
t
s
s
.
.
Terminal Cleaning
The i7910 must be off for all cleaning operations.
Do not clean the i7910 with water but with a dry or only slightly damp cloth. Do not use solvent, detergent
or abrasive products.
If the terminal has battery charging problem, clean the contacts on the battery and on the terminal with a
damp cloth. Do not scratch or scrape the surface of the contacts.
If the print quality deteriorates, clean the print head to remove accumulated paper dust. The print head
must be cleaned with the terminal powered off, using ethanol applied on a lint-free cloth.
Be aware of the sharp paper cutter and hot printer parts. Ensure that the ethanol has completely
evaporated before switching the terminal back on.
D
D
o
o
n
n
o
o
t
t
u
u
s
s
e
e
I
I
s
s
o
o
p
p
r
r
o
o
p
p
y
y
l
l
a
a
l
l
c
c
o
o
h
h
o
o
l
l
-
-
b
b
a
a
s
s
e
e
d
d
c
c
l
l
e
e
a
a
n
n
i
i
n
n
g
g
p
p
r
r
o
o
d
d
u
u
c
c
t
t
s
s
.
.
Replacing the Paper Roll
The paper roll usually has a low paper warning.
When a coloured stripe (usually red or green)
appears on the receipts or reports, it is time to
replace the paper roll:
1. Push the button on the paper compartment cover
toward the back and lift the cover.
2. Remove the empty paper roll.
3. The end of the paper ribbon is usually glued to
the rest of the new roll. Separate it so that it
becomes loose.
4. Place the new paper roll into the compartment. The loose end of the paper roll should come from the
lower side of the roll.
5. Close the cover, press it until it snaps.
6. Power up the unit and press the blue ‘Paper Feed’ key to verify the paper feeds properly.
7. Tear off the excess of paper coming out from the printer.
To Next Page
Loading...
Need help?
General
