Inovance MD500T75G - Page 86

6. Parameter Table MD500 User Manual
- 86 -
Function Code Parameter Name Setting Range Default Property
F0-23 Retentive of digital setting
frequency upon stop
0, 1 0
ƿ
F0-24 Motor parameter group selection 0: Motor parameter group 1
1: Motor parameter group 2
0
ƾ
F0-25 $FFHOHUDWLRQ'HFHOHUDWLRQ
time base frequency
0 to 2 0
ƾ
F0-26 %DVHIUHTXHQF\IRU83'2:1
PRGLÀFDWLRQGXULQJUXQQLQJ
0, 1 0
ƾ
F0-27 Binding command source
to frequency source
WR 000
ƿ
F0-28 Serial port communication
protocol
0, 1 0
ƾ
Group F1: Motor 1 Parameters
F1-00 Motor type selection
0, 1 0
ƾ
F1-01 Rated motor power
0.1 to 1000.0 kW Model
dependent
ƾ
F1-02 Rated motor voltage
1 to 2000 V Model
dependent
ƾ
F1-03 Rated motor current
WR$$&GULYHSRZHUN:
0.1 to 6553.5 A (AC drive power > 55 kW)
Model
dependent
ƾ
F1-04 Rated motor frequency
0.01 Hz to max. frequency Model
dependent
ƾ
F1-05 Rated motor speed
1 to 65535 rpm Model
dependent
ƾ
F1-06 Stator resistance
WRȎ$&GULYHSRZHUN:
WRȎ$&GULYHSRZHU!N:
Auto-tuning
dependent
ƾ
F1-07 Rotor resistance
WRȎ$&GULYHSRZHUN:
WRȎ$&GULYHSRZHU!N:
Auto-tuning
dependent
ƾ
F1-08 Leakage inductive reactance
WRP+$&GULYHSRZHUN:
0.001 to 65.535 mH (AC drive power > 55 kW)
Auto-tuning
dependent
ƾ
) Mutual inductive reactance
WRP+$&GULYHSRZHUN:
0.01 to 655.35 mH (AC drive power > 55 kW)
Auto-tuning
dependent
ƾ
F1-10 No-load current
$WR)$&GULYHSRZHUN:
0.1 A to F1-03 (AC drive power > 55 kW)
Auto-tuning
dependent
ƾ
F1-27 Encoder pulses per revolution 1 to 65535 1024
ƾ
F1-28 Encoder type 0: ABZ incremental encoder
2: Resolver
0
ƾ
F1-30 $%SKDVHVHTXHQFHRI$%=
incremental encoder
0: Forward
1: Reserve
0
ƾ
F1-34 Number of pole pairs of resolver 1 to 65535
ƾ
F1-36 Encoder wire-break
fault detection time
0.0s: No detection
0.1s to 10.0s
0.0s
ƾ
F1-37 Auto-tuning selection 0: No auto-tuning
1: Static auto-tuning 1
2: Dynamic auto-tuning
3: Static auto-tuning 2
0
ƾ
Group F2: Vector Control Parameters
F2-00 Speed loop proportional gain 1 1 to 100 30
ƿ
F2-01 Speed loop integral time 1 0.01s to 10.00s 0.50s
ƿ
efesotomasyon.com