How to troubleshoot no sound from one speaker on Insignia LCD TV?
If there is no output from one of the speakers on your Insignia LCD TV, adjust the audio balance. Also, make sure that the audio cables are connected correctly and securely to your TV.
Why does my Insignia LCD TV have no picture and sound?
If your Insignia LCD TV has no picture and no sound, try the following: - Press on the TV or the remote control. - Ensure the power cord is plugged in. - Verify video cables are securely connected to your TV. - Select the correct video input source. - Try another channel to rule out station issues. - Ensure the incoming signal is compatible. - Check that your antenna or cable TV is correctly and securely connected. - Adjust the contrast and brightness. - Ensure the Audio Only option is set to Off. - Check the closed caption settings, as some TEXT modes can block the screen.
Why is my Insignia LCD TV remote not working?
If your Insignia LCD TV remote control isn't working, ensure the power cord is correctly connected to the TV and a power outlet. Also, make sure there are no obstructions between the remote and the sensor on the front of the TV, and point the remote directly at the sensor. Check that the batteries are installed correctly (after removing any plastic wrapping) and replace them if necessary.
How to fix sound on Insignia NS-32E740A12 LCD TV?
If your Insignia LCD TV has good picture but no sound, first, increase the volume and make sure that the sound is not muted. Disconnect any headphones that may be plugged in. Ensure the correct audio mode is selected and that the audio cables are connected correctly and securely. Check that the antenna or cable TV is connected correctly and securely and that the digital channel signal is not low (if using an antenna). Finally, the audio cables you are using may be faulty, so try a new set.
Why is the picture dark on my Insignia NS-32E740A12 LCD TV but the sound is fine?
If your Insignia LCD TV has a dark, poor, or no picture (but the screen is lit) while the sound is good, try switching to another channel to rule out station-specific problems. Ensure that the antenna or cable TV is connected correctly and securely. Adjust the brightness and make sure that the correct picture mode is selected. If you are using an antenna, the digital channel signal may be low, so consider adjusting the antenna or using a highly directional outdoor antenna or set-top antenna with a built-in amplifier. Also, ensure that the video cables are connected securely and try a new set of video cables, as the ones you are using may be bad.
How to adjust color on Insignia LCD TV?
If your Insignia LCD TV shows no color, a dark picture, or incorrect colors, try changing the channel to rule out station issues. Adjust the color settings and ensure that the video cables and the antenna or cable TV are connected correctly and securely. If you are using an antenna, the digital channel signal may be low, so consider adjusting the antenna or using a highly directional outdoor antenna or set-top antenna with a built-in amplifier.
Why no channels after auto search on Insignia NS-32E740A12?
If there are no channels after running Auto Channel Search on your Insignia LCD TV, reception can vary by channel depending on the broadcast power level of a given station, so contact your cable or satellite TV provider. Also, make sure the antenna or cable/satellite TV is connected securely to your TV and try replacing the cable between the antenna/cable or cable/satellite box and your TV.
How to prevent after images on Insignia NS-32E740A12?
To prevent after images on your Insignia LCD TV, avoid displaying a still image, such as a logo, game, or computer image, for an extended period. This can cause a permanent after-image to be burned into the screen, which is not covered by your warranty.
How to eliminate audio noise from Insignia LCD TV?
If you are experiencing audio noise with your Insignia LCD TV, other devices may be interfering with your TV. Try turning off one device at a time to determine which device is causing interference and move it further from the TV.
How to improve poor picture quality on Insignia NS-32E740A12 LCD TV?
If your Insignia LCD TV has a poor picture, ensure that the room is not too bright, as light reflecting off the screen can make the picture difficult to see. If an S-VHS camera or camcorder is connected while another device is turned on, the picture may be poor, so try turning off one or more devices.
General| Response time | 9 ms |
|---|---|
| Display diagonal | 31 \ |
| Display brightness | 350 cd/m² |
| Display resolution | 1366 x 768 pixels |
| Native aspect ratio | 16:9 |
| Supported video modes | 1080p |
| Contrast ratio (dynamic) | 5000:1 |
| Contrast ratio (typical) | 1200:1 |
| Supported graphics resolutions | 1366 x 768 |
| 3D | No |
| Backlight | - |
| HDMI ports quantity | 3 |
| DVI-D ports quantity | 1 |
| DVI-I ports quantity | 2 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| S-Video inputs quantity | 0 |
| Product color | Black |
| Panel mounting interface | 200 x 100 mm |
| RMS rated power | - W |
| Power consumption (standby) | 1 W |
| Power consumption (typical) | 64 W |
| Remote control type | Standard |
Weight and Dimensions| Height (with stand) | 533.4000 mm |
|---|---|
| Weight (with stand) | 9888.3137 g |
| Depth (without stand) | 203.2000 mm |
| Width (without stand) | 736.6000 mm |
| Height (without stand) | 457.2000 mm |
| Weight (without stand) | 8164.6627 g |
Basic advice for safe TV operation and placement.
Guidelines for securely installing the TV on a wall.
Critical safety advice, including electric shock and handling the LCD panel.
Welcome, SRS TruSurround HD, and INlink features.
Step-by-step guide for physical setup.
Listing included items and identifying front controls.
Description of all available input/output jacks.
Detailed explanation of each button's purpose.
Guidance on selecting the best video/audio connection type.
Basic power connection steps.
Methods for connecting to TV sources.
How to connect broadcast signals without a box.
Instructions for connecting media players.
How to hook up entertainment devices.
Steps for PC connectivity via VGA or HDMI.
How to use the headphone jack.
Instructions for analog and digital audio outputs.
Guided process for initial configuration.
Turning on/off and selecting video sources.
How to interact with the on-screen display.
Procedures for changing channels and adjusting audio levels.
Customizing visual settings for optimal display.
How to display current program details.
Customizing sound profiles and features.
How to listen to audio without the picture.
Automatic search for available TV channels.
Securing TV access and device controls.
Restricting programs without ratings.
Configuring content restrictions by region.
Enabling and disabling subtitle features.
Selecting display styles for analog captions.
Personalizing digital subtitle appearance.
Configuring the TV's internal clock.
Scheduling automatic TV turn-off.
Changing the on-screen display language.
Customizing names for connected devices.
Managing automatic input detection and resetting preferences.
Controlling HDMI CEC devices and power settings.
Automating device power and controlling receiver volume.
Viewing connected HDMI CEC devices.
Accessing files from a USB drive.
Navigating and viewing image files.
Displaying images automatically.
Adjusting playback options for slideshows.
Instructions for cleaning the cabinet and screen.
Solutions for video, audio, and remote problems.
Detailed hardware and performance data.
Instructions and codes for using third-party remotes.
FCC, cable, and trademark compliance statements.
Coverage, claims, and exclusions.
To Next Page