20
NS-32E740A12 Insignia 32" LED-LCD HDTV, 720p
www.insigniaproducts.com
Turning on your TV for the
first time
The first time you turn on your TV, the Setup Wizard
opens. The Setup Wizard guides you through
setting up basic settings including the menu
language, time setting, picture mode, TV signal
source, and the channel list.
To set up your TV:
1 Make sure that you have:
• Installed the remote control batteries. (See
page 19 for details).
• Connected an antenna, cable TV, or satellite
TV. (See page 10 or 13 for details.)
• Connected the power cord. (See page 10 for
details.)
2 Press (power) to turn on your TV. The Choose
Your Menu Language screen opens.
3 Press
or to highlight the language you
want, then press ENTER. The Choose Your Time
Setting screen opens.
4 Press
or to highlight Mode, then press
or to select Manual (to set the date and
time manually) or Auto (to set the date and time
automatically from a TV signal source based on
the time zone you select).
5 If you selected Auto for Mode, press
or to
highlight Time Zone, then press or to select
your time zone. You can select Newfoundland,
Atlantic, Eastern, Central, Mountain, Pacific,
Alaska, or Hawaii.
6 If you selected Auto for Mode, press
or to
highlight Daylight Savings, then press or
to select On (if your viewing area observes
Daylight Savings Time) or Off (if your viewing
area does not observe Daylight Savings Time).
7 If you selected Manual for Mode, set the date
by pressing
or to highlight Year, Month, or
Day, then press
or to adjust the setting.
8 If you selected Manual for Mode, set the time
by pressing
or to highlight Time, then
pressing or to select the hour, minute, or
AM/PM field. Press or to adjust the setting.
9 Press ENTER. The Choose Your Picture Mode
screen opens.
10 Press
or to highlight Home Mode or Retail
Mode, then press ENTER.
If you selected Retail Mode, a message appears
“Are you sure you want retail mode? In this
mode, ENERGY STAR savings are not realized.”
Select Ye s to continue, or select No to change
your selection.
The Choose Your TV Source screen opens.
11 Press
or to highlight Antenna, Cable, or
Cable/Satellite Box (if your cable TV uses a box,
select Cable/Satellite Box), then press ENTER.
If you chose Antenna or Cable, your TV
automatically starts scanning for channels
available in your viewing area. If you chose
Cable/Satellite box, your TV does not need to
scan for channels.
During auto channel search, your TV searches
for digital channels first. When the digital
channel search is complete, a message appears
asking if you want to search for analog channels.
Select Ye s to continue searching for analog
channels, or select No to stop searching for
channels.
12 To watch TV, press INPUT, press
or to
highlight TV in the Input Source list, then press
ENTER.
OK
ENTER
MENU
EXIT
English
Français
Español
Choose Your Menu Language
MOVE
EXIT
PREVIOUS
SELECT
Set menu language to English, Français, or Español
OK
ENTER
MENU
EXIT
Mode
Time Zone
Daylight Savings
Year
Month
Day
Time
If Automatic, options are automatically set by TV source
MOVE
EXIT
PREVIOUS
SELECT
Choose Your Time Setting
Auto
Pacific
On
2011
Jan
1
12:25 AM
Note
You can press EXIT to stop the auto channel search,
but you will need to run the auto channel search
again to create a channel list.
OK
ENTER
MENU
EXIT
Reduces total power consumption
Home Mode
Retail Mode
MOVE
EXIT
PREVIOUS
SELECT
Choose Your Picture Mode
OK
ENTER
MENU
EXIT
Digital Channels
Analog Channels
Scanning for digital channels
Choose Your TV Source
Antenna
Cable
Cable/Satellite Box
0
MOVE
EXIT
PREVIOUS
SELECT
Channel scan may take 20+ minutes
0
To Next Page
Loading...
Need help?
General
Weight and Dimensions
