Why is there no output from one of the speakers on my Insignia NS-42E859A11 LED TV?
If there's no output from one of the speakers on your Insignia LED TV: * Adjust the balance of the speakers. * Make sure that the audio cables are connected correctly and securely to the back of your TV.
What causes a 'ghost' or double image on Insignia LED TV?
A 'ghost' or double image on your Insignia LED TV may be caused by obstructions, such as high-rise buildings or hills, preventing your antenna from receiving a clear signal. Using a highly directional antenna may improve the picture quality.
Why is the Z-Wave remote control not working with my Insignia LED TV?
If your Z-Wave remote control isn't working with your Insignia LED TV: * Ensure the power cord is correctly connected to a power outlet. * Make sure the remote control is added to the Z-Wave network and paired with your TV. * Replace the batteries, aligning the + and – symbols correctly. * Confirm the remote control is in the correct device mode by pressing TV.
How to resolve audio noise on Insignia LED TV?
To resolve audio noise on your Insignia LED TV, other devices may be interfering with your TV. Try turning off one device at a time to determine which device is causing interference. Once you have determined which device is causing interference, move it further from the TV to eliminate the interference.
What to do if automatic network setup fails on Insignia LED TV?
If automatic network setup fails on your Insignia LED TV: * The DHCP service is not enabled on the router, or no router is present. Refer to your router’s documentation for instructions on enabling DHCP. If you do not have a router, you must manually set up the network address. * Internet service is not available. Check your cable or DSL modem or contact your ISP for Internet service issues.
Why is my Insignia NS-42E859A11 LED TV showing only snow or noise?
If your Insignia LED TV screen displays only snow (noise): * Try another channel, as the station may be experiencing problems. * Ensure the antenna or cable TV is connected correctly and securely. * If using an antenna, the digital channel signal may be low. To check the digital channel signal strength, see “Checking the signal strength” on page 70. * If you are using an antenna and the signal strength is low, adjust the antenna or use a highly directional outdoor antenna or set-top antenna with a built-in amplifier.
Why is the picture not filling the screen on my Insignia NS-42E859A11 LED TV?
If the picture on your Insignia LED TV doesn't fill the screen and there are black bars, change the aspect ratio. Digital TV and movies are increasingly presented in wide screen (16:9).
What causes a horizontal dotted line on Insignia NS-42E859A11 LED TV?
A horizontal dotted line on your Insignia LED TV can be caused by: * The antenna or cable TV not being connected correctly and securely. * A low digital channel signal if you're using an antenna. To check the signal strength see “Checking the signal strength” on page 70. * Bad video cables. Try a new set. * Other devices interfering with your TV. Try turning off one device at a time to determine which device is causing interference. Once you have determined which device is causing interference, move it further from the TV to eliminate the interference. If you are using an antenna and the signal strength is low, adjust the antenna or use a highly directional outdoor antenna or set-top antenna with a built-in amplifier.
How to troubleshoot no network connection on Insignia NS-42E859A11 LED TV?
To troubleshoot a missing network connection on your Insignia LED TV: * Ensure your TV and modem or router are securely connected. * Verify your network address is set up correctly. Also, make sure your wireless access point is turned on and set up correctly.
What to do if Insignia NS-42E859A11 displays 'searching for a signal'?
If your Insignia LED TV displays 'searching for a signal on this source' and never shows a picture: * Press INPUT and ensure you've selected the correct input for the device or service you're using. * If using a cable or satellite box, use its remote to change channels. * Ensure you've selected the correct input to view channels from the cable or satellite box.
General| Display diagonal | 42 \ |
|---|---|
| Display brightness | 450 cd/m² |
| Supported video modes | 1080p |
| Contrast ratio (dynamic) | 12000:1 |
| Screen format adjustments | 16:9 |
| Supported graphics resolutions | 1920 x 1080 (HD 1080) |
| 3D | No |
| Backlight | - |
| Headphone connectivity | 3.5 mm |
| HDMI ports quantity | 4 |
| DVI-D ports quantity | 1 |
| DVI-I ports quantity | 0 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Compatible memory cards | Not supported |
| Product color | Black |
| Panel mounting interface | 200 x 200 mm |
| RMS rated power | - W |
| Number of speakers | 3 |
| Power consumption (standby) | 1 W |
| Power consumption (typical) | 115 W |
| Remote control type | Standard |
Weight and Dimensions| Depth (with stand) | 279.4000 mm |
|---|---|
| Weight (with stand) | 17780.8209 g |
| Depth (without stand) | 50.8000 mm |
| Width (without stand) | 990.6000 mm |
| Height (without stand) | 609.6000 mm |
| Weight (without stand) | 14605.6743 g |
Tips for safe usage and placement of flat panel displays to prevent injury.
Detailed safety guidelines and warnings for operating and maintaining the TV.
Important cautions regarding power lines, LCD panel, service, and outdoor antenna grounding.
Steps for connecting various external devices and power to the TV.
Steps for initial TV setup using the Setup Wizard.
How to customize picture settings for optimal viewing experience.
Options for manually adjusting sound levels and audio features.
Configuring wired or wireless network connections for internet access.
Step-by-step guide to configure the TV as the primary hub for the Rocketboost network.
Solutions for issues like no power, no picture, audio problems, and remote control failures.
Guide to reset the TV to its original factory settings and re-run setup.
Instructions for adding the remote to the Z-Wave network and toggling between IR/RF modes.
To Next Page
