60
En
■ Lip Sync
Disable
:
HDMI lip sync disabled.
Enable:
HDMI lip sync enabled.
The AV controller can be set to automatically correct any
delay between the video and the audio, based on the data
from the connected monitor.
• This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
• You can check the amount of delay being applied by the HDMI
Lip Sync function on the A/V Sync screen.
•If the “Monitor Out” setting is set to “HDMI Main”,
“Both(Main)” or “Both” (➔ 45), the delay will be corrected in
accordance with the monitor connected to HDMI OUT MAIN.
On the other hand, if “HDMI Sub” or “Both(Sub)” is selected,
the delay will be corrected in accordance with the monitor con-
nected to HDMI OUT SUB.
■ HDMI Control (RIHD)
Off
:
p disabled.
On:
p enabled.
This function allows p-compatible components
connected via HDMI to be controlled with the AV control-
ler (➔ 96 to 97).
• When set to “On” and close the menu, the name of connected
p-compatible components and “RIHD On” are dis-
played on the AV controller.
“Search...” “(name)” “RIHD On”
When the AV controller cannot receive the name of the compo-
nent, it is displayed as “Player*” or “Recorder*”, etc (“*”
means the number of two or more component).
When set to “Off” and close the menu, “RIHD Off” are dis-
played on the AV controller.
“Disconnect” “RIHD Off”
• When an p-compatible component is connected to the
AV controller via the HDMI cable, the name of the connected
component is displayed on the AV controller display. For exam-
ple, while you are watching TV broadcasting, if you operate a
Blu-ray Disc/DVD player (being powered on) by the remote
control of the AV controller, the name of the Blu-ray Disc/DVD
player is displayed on the AV controller.
•Set to
“Off” when a connected piece of equipment is not com-
patible or it is unclear whether the equipment is compatible or
not.
• If movement is unnatural when set to
“On”, change the setting
to
“Off”.
• Refer to the connected component’s instruction manual for
details.
•The p control does not support HDMI OUT SUB. Use
HDMI OUT MAIN instead.
• When the source equipment is connected with the u connec-
tion, it may malfunction if “HDMI Control (RIHD)” is set to
“On”.
■ Audio Return Channel
Off:
Select “Off” if you don’t want to use audio return
channel (ARC) function.
Auto
:
The audio signal from your TV tuner can be sent to
the HDMI OUT MAIN of the AV controller.
Audio return channel (ARC) function enables an HDMI
(Audio Return Channel) capable TV to send the audio
stream to the HDMI OUT MAIN of the AV controller. To
use this function, you must select the TV/CD input selec-
tor and your TV must support ARC function.
•The “Audio Return Channel” setting can be set only when the
“HDMI Control (RIHD)” setting is set to “On”.
• This setting is set to “Auto” automatically when the “HDMI
Control (RIHD)” is set to “On” first time.
■ Power Control
Off:
Power Control disabled.
On
:
Power Control enabled.
To link the power functions of p-compatible com-
ponents connected via HDMI, select “On”.
This setting is set to “On” automatically when the
“HDMI Control (RIHD)” is set to “On” first time.
•The “Power Control” setting can be set only when the “HDMI
Control (RIHD)
” setting is set to “On”.
• HDMI power control only works with p-compatible
components that support it and may not work properly with
some components due to their settings or compatibility.
• When set to “On”, power consumption will increase.
• When set to “On”, regardless of whether the AV controller is On
or in Standby, both audio and video stream from an HDMI input
will be output to the TV or other components via HDMI connec-
tion (HDMI pass through function).
• The power consumption during standby mode will increase dur-
ing the HDMI pass through function; however if your TV sup-
ports CEC (Consumer Electronics Control), the power
consumption can be saved in the following cases:
1. The TV is in standby mode.
2. You are watching a TV program.
• Refer to the connected component’s instruction manual for
details.
To Next Page
Loading...
Need help?
General
