ITI Concord - The Touchpad Tamper Feature; Changing or Erasing User Codes; Changing a User Code; Erasing a User Code

12
Changing or Erasing User Codes
Changing a User Code
Note: To change System and Partition Master codes
please see page 42.
To change or assign a user code:
1. Enter the programming menus by pressing
9
+ System or Partition Master
CODE
.
2. Press
030
nn
0
where nn is the user 00
through 59.
3. Enter the desired 4-digit code, then
ƒ
.
4. Press
‚
+
00
+
ƒ
to exit the programming
menus.
Note: The system will not accept the same code for
two different users.
Erasing a User Code
When a code is deleted from the system, that code no
longer acts as a key for operating the system in any man-
ner.
To erase a user code:
1. Enter the programming menus by pressing
9
+ System or Partition Master
CODE
.
2. Press
030
nn
0
where nn is user 00
through 59.
3. Enter the System or Partition Master
CODE
,
then
ƒ
.
4. Press
‚
+
00
+
ƒ
to exit the programming
menus.
Assigning Code Attributes
Code attributes determine what a person using their code
can do. You will want certain users to have more control
over the system than others. For example, you would
want an adult to have more control over the system than
a child. Below are code attributes that you can assign.
Assigning the Direct Bypassing Attribute
Direct Bypassing is a user code attribute that allows the
user to bypass open sensors. If the user code does not
have this attribute turned on, the user will not be able to
bypass sensors directly.
To assign Direct Bypassing to a user:
1. Enter the programming menus by pressing
9
+ System or Partition Master
CODE
.
2. Press
030
nn
1
where nn is user 00
through 59.
3. To turn Direct Bypassing:
• on, press
2
+
ƒ
.
• off, press
1
+
ƒ
.
4. Press
‚
+
00
+
ƒ
to exit the programming
menus.
Assigning the Remote Access Attribute
Remote Access is a user code attribute that allows the
user to access the security system from a telephone. If the
user code does not have this attribute turned on, the user
will not be able to access the system by off-premises
telephones.
To assign Remote Access to a user:
1. Enter the programming menus by pressing
9
+ System or Partition Master
CODE
.
2. Press
030
nn
2
where nn is user 00 through
59.
3. To turn Remote Access:
• on, press
2
+
ƒ
.
• off, press
1
+
ƒ
.
4. Press
‚
+
00
+
ƒ
to exit the programming
menus.
Assigning the Partition Jump Attribute
Partition Jump is a user code attribute that allows the user
to access both partitions. If the user code does not have
this attribute turned on, the user will not be able to access
both partitions.
To assign Partition Jump to a user:
1. Enter the programming menus by pressing
9
+ System or Partition Master
CODE
.
2. Press
030
nn
3
where nn is user 00
through 59.
3. To turn Partition Jump:
• on, press
2
+
ƒ
.
• off, press
1
+
ƒ
.
4. Press
‚
+
00
+
ƒ
to exit the programming
menus.
The Touchpad Tamper Feature
The installer can program your system to send a
Police alarm in the case of possible touchpad tamper-
ing.
If more than 40 keys are pressed when the system
asks for a code, and those keystrokes are not part of
a valid access code, a siren will sound. Talk to your
installer or see Appendix A “Touchpad Information”
on page 35 to see if this feature is enabled.
A Touchtone phone can be used to change or erase
user codes, but alphanumeric or fixed display touch-
pads work much better because of their extensive
feedback. See Appendix C for phone programming
instructions.